Active AP_PW
ACTIVE 2.0 Electric Pressure Washer Instruction Manual
Model: AP_PW
Introduction
This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your ACTIVE 2.0 Electric Pressure Washer. Please read this manual thoroughly before initial use and keep it for future reference.
Safety Information
Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury. Keep children and pets away from the operating area. Wear appropriate personal protective equipment (PPE) including eye protection.
WARNING: High-pressure spray can cause serious injury. Never direct the spray at people, pets, or electrical devices.
Product Overview
The ACTIVE 2.0 Electric Pressure Washer is a compact and powerful cleaning tool designed for various outdoor tasks. It features a patented 5-Piston Pro Pump for enhanced durability and performance.

Figure 1: Main unit of the ACTIVE 2.0 Electric Pressure Washer.

Figure 2: Included accessories: 20' rubber hose, metal spray gun & wand, detergent foam cannon, and 4 metal spray tips (0°, 15°, 25°, 40°).
Setup
- Unpacking: Carefully remove all components from the packaging. Verify all parts are present according to the packing list.
- Water Supply Connection: Connect a standard garden hose to the water inlet of the pressure washer. Ensure the connection is secure to prevent leaks. The unit requires a minimum flow rate to operate correctly.
- High-Pressure Hose Connection: Attach the high-pressure hose to the outlet of the pressure washer and to the spray gun. Tighten all connections firmly.
- Nozzle Selection: Choose the appropriate spray tip for your task. Insert the desired tip into the quick-connect fitting on the spray wand.

Figure 3: Different spray nozzles for varied applications (0°, 15°, 25°, 40°).
- Power Connection: Plug the power cord into a grounded electrical outlet. Ensure the power switch is in the "OFF" position before plugging in.
Video 1: Unboxing and initial setup of the Active 2.0 Pressure Washer, showing the components included in the box.
Operating Instructions
- Start-up:
- Turn on the water supply completely.
- Squeeze the trigger on the spray gun to purge air from the pump and hose until a steady stream of water emerges.
- Turn the power switch to the "ON" position. The motor will start.
- Operation:
- Point the spray gun at the cleaning surface, keeping a safe distance.
- Squeeze the trigger to begin spraying. The unit features a Total Stop System (TSS) which automatically shuts off the pump when the trigger is released, prolonging pump life.
- Adjust the distance and angle of the spray to suit the cleaning task.
- Using the Detergent Foam Cannon:
- Fill the detergent foam cannon with appropriate pressure washer detergent.
- Attach the foam cannon to the spray gun's quick-connect fitting.
- Spray the detergent onto the surface. Allow it to dwell for a few minutes before rinsing.
- Shut-down:
- Turn the power switch to the "OFF" position.
- Turn off the water supply.
- Squeeze the spray gun trigger to release any remaining pressure in the system.
- Disconnect the high-pressure hose and garden hose.
Video 2: Demonstration of the Active 2.0 Electric Pressure Washer in use for car washing, highlighting its 2.0 GPM flow.
Maintenance
- After Each Use:
- Drain all water from the pump and hoses to prevent freezing and damage.
- Clean the spray tips and ensure they are free of debris.
- Wipe down the unit with a damp cloth.
- Storage: Store the pressure washer in a dry, frost-free environment.
- Pump Care: For extended storage or in freezing temperatures, use a pump protector or non-toxic antifreeze to lubricate and protect the pump.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not start | No power supply; tripped circuit breaker; power switch off. | Check power connection; reset breaker; turn power switch ON. |
| Low pressure | Insufficient water supply; clogged nozzle; air in pump. | Ensure full water flow; clean nozzle; purge air from system. |
| Water leaks from connections | Loose connections; worn O-rings. | Tighten connections; replace O-rings if damaged. |
Specifications
- Brand: Active
- Model: AP_PW
- Maximum Pressure: 1800 PSI
- Maximum Flow Rate: 2.0 GPM
- Power Source: Electric (AC)
- Motor: 1800W
- Pump Type: Patented 5-Piston Pro Pump
- Hose Length: 20 Feet
- Product Dimensions: 16"L x 9"W x 8"H
- Item Weight: 24.1 pounds
- UPC: 841308103099
Warranty and Support
For warranty information, technical support, or to order replacement parts, please visit the official Active website or contact customer service. Keep your purchase receipt for warranty claims.
Official Store: Active Store on Amazon
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.







