ROCKBROS 115dB Wireless Vibration Motion Sensor Bike and Motorcycle Alarm Instruction Manual

Introduction

This manual provides detailed instructions for the proper installation, operation, and maintenance of your ROCKBROS 115dB Wireless Vibration Motion Sensor Bike and Motorcycle Alarm. Please read this manual thoroughly before using the product to ensure safe and effective operation.

Safety Information

• Ensure the alarm is securely mounted to prevent accidental detachment during vehicle operation.
• Avoid direct exposure to extreme temperatures or prolonged sunlight, which may affect battery life and performance.
• Do not attempt to disassemble or modify the alarm unit or remote control, as this may void the warranty and cause malfunction.
• Keep the remote control away from water and moisture.
• The alarm produces a loud sound (115dB). Avoid prolonged exposure to prevent hearing damage.

Package Contents

Please verify that all items are present in your package:

• ROCKBROS 115dB Alarm Unit
• Remote Control
• USB Type-C Charging Cable
• Mounting Bracket
• Zip Ties for Installation
• Double-sided Adhesive Pad
• User Manual (this document)

Setup and Installation

1. Initial Charging

Before first use, fully charge the alarm unit using the provided USB Type-C cable. The blue LED on the remote will indicate charging status.

Image: The alarm unit connected to a power source via a USB Type-C cable for charging. The image highlights the charging port and the compact design of the alarm.

2. Mounting the Alarm Unit

The alarm unit can be mounted in various locations on your bicycle or motorcycle using the provided zip ties or double-sided adhesive. Choose a discreet and secure location.

• Using Zip Ties: Secure the mounting bracket to your desired location (e.g., seat post, handlebar, frame) using the zip ties. Ensure it is tight and stable.
• Using Adhesive: Clean the surface thoroughly. Apply the double-sided adhesive to the back of the alarm unit and firmly press it onto the chosen surface.

Image: The alarm unit and remote control mounted on a bicycle handlebar. The alarm is secured with zip ties, and the remote is attached to a separate bracket.

Image: The alarm unit mounted discreetly under the bicycle seat. This shows a common and effective placement for the alarm.

Image: The alarm unit mounted on the front fork of a bicycle. This illustrates another possible installation point.

Image: The alarm unit mounted on the top tube of a bicycle frame. This provides an alternative mounting option.

Operating Instructions

Your ROCKBROS alarm system is controlled by a wireless remote with multiple functions:

Image: A close-up of the remote control, illustrating the four main buttons: Arming/Sensitivity, Disarming/Function Settings, Panic Alarm/Volume, and Bell/Ringtone Options.

1. Arming and Disarming the Alarm

• To Arm: Press the Lock button (top left) on the remote. The alarm will emit a "do-re-mi" sound, indicating it is armed. It will enter alert mode after 5 seconds.
• To Disarm: Press the Unlock button (top right) on the remote. The alarm will emit a "mi-re-do" sound, indicating it is disarmed.

2. Adjusting Sensitivity and Volume

You can customize the alarm's sensitivity and volume levels:

• Sensitivity Adjustment: Press and hold the Unlock button for 6 seconds until the blue LED on the remote stays lit. Then, press the Lock button repeatedly to cycle through 3 sensitivity levels (low, medium, high). Each press will indicate a different level.
• Volume Adjustment: While in sensitivity adjustment mode (blue LED lit), press the Panic Alarm/Volume button repeatedly to cycle through 5 volume levels. Each press will indicate a different volume.
• Exit Adjustment Mode: Press the Lock button to save settings and exit.

3. Panic Alarm / Bike Search

• Panic Alarm: Press the Panic Alarm/Volume button (bottom left) to trigger a loud, continuous alarm sound ("biu-biu-biu") to deter potential thieves or locate your vehicle in a crowded area. Press the Unlock button to stop the panic alarm.
• Bike Search: Press the Bell/Ringtone button (bottom right) to make the alarm unit emit a short sound, helping you locate your bike.

4. Ringtone Options (Electric Bell)

• Change Ringtone: Press and hold the Bell/Ringtone button (bottom right) to cycle through 5 different ringtone options for the electric bell function.
• Activate Bell: A short press of the Bell/Ringtone button will activate the selected ringtone.

Maintenance

Remote Control Battery Replacement

The remote control uses a 12V 27A alkaline battery. When the remote's range decreases or it becomes unresponsive, it's time to replace the battery.

1. Using a small flat-blade screwdriver, gently pry open the remote control housing at the notch located in the lower right corner.
2. Carefully remove the circuit board, ensuring not to touch the components directly to avoid static discharge.
3. Remove the old 12V 27A alkaline battery. Note the polarity (+/-) before removing.
4. Insert the new 12V 27A alkaline battery, matching the correct polarity.
5. Place the circuit board back into the chassis, aligning it with the slots in the housing.
6. Fasten the upper and lower covers of the remote control until they click securely into place.

Troubleshooting

Specifications

• Brand: ROCKBROS
• Model Number: 34210004001-YXUS
• Noise Level: 115 Decibels
• Maximum Remote Range: 262 Feet
• Compatible Devices: Bike, Motorcycle
• Alarm Unit Battery: Rechargeable (Type-C)
• Remote Control Battery: 1 x 12V 27A (included)
• Features: Vibration Motion Sensor, Waterproof, Wireless Remote
• Item Weight: 4.9 ounces
• Package Dimensions: 5.79 x 4.17 x 1.93 inches

Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact ROCKBROS customer service directly through their official website or the retailer where the product was purchased. Keep your proof of purchase for warranty claims.