FrSky Tandem X20 HD
Contents
FrSky Tandem X20 HD Transmitter User Manual
Model: Tandem X20 HD
Introduction
The FrSky Tandem X20 HD radio system is an advanced digital video transmission system designed for FPV flying enthusiasts. It integrates an FPV screen with 720p 60FPS video quality, eliminating the need for separate display equipment. This system combines near 0ms low latency digital video transmission with robust radio control capabilities, enhancing the FPV flying experience. It is compatible with HDZero video transceiver (VTX) products.
Product Overview
The Tandem X20 HD Transmitter features a comprehensive design for intuitive control and high-performance operation. Key components and features include:
- Integrated HD Digital Video Transmission: Supports 720P 60FPS with near 0ms latency.
- Dual-Band Internal RF Module: TD 900M/2.4G module supporting ACCST D16, ACCESS, and TD modes.
- High-Resolution Touch-Screen: 800x480 color display for clear interface navigation.
- Precision Control: High-Precision Hall-Sensor Gimbals with CNC metal panel.
- User-Friendly Interface: ETHOS operating system with clear UI design, supporting dual operation modes (touch and non-touch).
- Customizable Controls: 6 Quick-Mode custom buttons (front) and 2 momentary buttons (rear).
- Telemetry and Long Range: Up to 50-100KM range with telemetry feedback and down to 4ms end-to-end latency.
- Accessibility Features: Haptic vibration alerts and voice speech outputs.
- Power Management: Supports recharge system for 2S Li-ion battery via USB Type-C.

Figure 1: Front view of the FrSky Tandem X20 HD Transmitter, showing the integrated screen, gimbals, and control buttons.

Figure 2: The FrSky Tandem X20 HD Transmitter displaying the ETHOS operating system menu on its integrated screen.

Figure 3: Rear view of the FrSky Tandem X20 HD Transmitter, showing the battery compartment and external module bay.
Setup Guide
Follow these steps for the initial setup of your FrSky Tandem X20 HD Transmitter:
- Unboxing and Inspection: Carefully remove all components from the packaging. Inspect the transmitter for any signs of damage.
- Battery Installation and Charging: The transmitter uses a 2S Li-ion battery. Ensure it is properly installed. Connect the included USB Type-C cable to the transmitter and a compatible USB power source (e.g., computer USB port, USB wall adapter) to charge the battery. The charging indicator will show the status.
- Power On: Press and hold the power button located on the front panel until the screen illuminates.
- Initial Configuration: Upon first power-on, the ETHOS operating system may guide you through initial setup steps such as language selection, date/time setting, and basic calibration. Follow the on-screen prompts.
- Antenna Connection: Ensure the 5.8G circularly polarized directional external antennas are securely connected to their respective ports on the top of the transmitter.
- Firmware Update (Optional): It is recommended to check for the latest firmware updates on the FrSky official website to ensure optimal performance and access to new features. Refer to the official FrSky documentation for detailed firmware update procedures.
Operating Instructions
This section provides general guidance on operating your Tandem X20 HD Transmitter. For detailed instructions on specific functions, refer to the comprehensive ETHOS operating system manual available on the FrSky website.
Navigating the ETHOS System
- Touch Screen: Use the integrated touch screen to navigate menus, select options, and input data.
- Navigation Buttons/Scroll Wheels: Utilize the physical buttons and scroll wheels for precise navigation and adjustments, especially in non-touch mode.
- Quick-Mode Buttons: The 6 front and 2 rear momentary buttons can be customized for quick access to frequently used functions or flight modes.
Binding a Receiver
To establish communication between your transmitter and a receiver (e.g., ACCST D16, ACCESS, or TD series receiver), follow the binding procedure outlined in your receiver's manual and the ETHOS system's binding menu. Generally, this involves:
- Power on the transmitter and navigate to the Model Setup menu.
- Select the internal RF module and choose the desired mode (e.g., ACCESS, TD).
- Initiate the binding process on the transmitter.
- Place your receiver into binding mode (refer to receiver manual).
- Once bound, the receiver's LED indicator will confirm successful connection.
FPV Video Display
The integrated screen displays the FPV video feed from compatible HDZero VTX products. Ensure your VTX is properly configured and powered. The transmitter's built-in video receiver module will automatically detect and display the video signal. The HDMI output port allows connection to an external monitor if desired.

Figure 4: Angled view of the FrSky Tandem X20 HD Transmitter showing an FPV video feed displayed on its integrated screen.
Maintenance and Care
Proper maintenance ensures the longevity and reliable performance of your FrSky Tandem X20 HD Transmitter:
- Cleaning: Use a soft, dry cloth to clean the transmitter's surface. For the screen, use a microfiber cloth specifically designed for electronics. Avoid abrasive cleaners or solvents.
- Storage: Store the transmitter in a cool, dry place away from direct sunlight, extreme temperatures, and high humidity. Use a protective case when transporting.
- Battery Care: Do not overcharge or deep discharge the Li-ion battery. If storing for extended periods, charge the battery to approximately 50% capacity.
- Gimbal Protection: When not in use, ensure the gimbals are protected from impact or pressure.
- Antenna Care: Handle the external antennas with care to avoid bending or damaging them.
Troubleshooting
This section addresses common issues you might encounter. For more complex problems, refer to the official FrSky support resources.
| Problem | Possible Cause | Solution |
|---|---|---|
| Transmitter does not power on. | Low or depleted battery; incorrect battery installation. | Charge the battery using the USB Type-C port. Ensure the battery is correctly installed. |
| No FPV video on screen. | VTX not powered or configured; incompatible VTX; antenna issue. | Verify VTX power and settings. Ensure VTX is HDZero compatible. Check antenna connections on both transmitter and VTX. |
| Receiver not binding. | Incorrect RF mode selected; receiver not in binding mode; distance too far. | Ensure the correct RF mode (ACCST D16, ACCESS, TD) is selected on the transmitter. Put the receiver into binding mode. Try binding at a closer distance. |
| Gimbal calibration issues. | Gimbals require recalibration. | Navigate to the calibration menu in ETHOS and follow the on-screen instructions to recalibrate the gimbals. |
Technical Specifications
| Feature | Specification |
|---|---|
| Model | Tandem X20 HD |
| Dimensions | Approximately 5 x 5 x 5 inches |
| Display Resolution | 800*480 Color Touch-Screen LCD |
| Video Transmission | 720P 60FPS HD Digital Video (near 0ms latency) |
| Video Encoding | H.264, H.265/HEVC |
| RF Module | Built-in TD 900M/2.4G Dual-Band Internal RF Module |
| Compatibility | ACCST D16, ACCESS, TD series receivers; HDZero VTX products |
| Control Latency | Down to 4ms end-to-end |
| Control Range | Up to 50 to 100KM (dependent on VTX power setting) |
| Gimbals | High-Precision Hall-Sensor Gimbals with All-CNC Metal Panel |
| Connectivity | USB Type-C (charging), HDMI Output |
| Special Features | Touchscreen, 6-axis Gyroscope Sensor, Haptic Vibration, Voice Speech Outputs, PARA Wireless Training System |
| Operating System | ETHOS |
Warranty and Support
FrSky products are manufactured to high standards and undergo rigorous quality control. For information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or visit the official FrSky website.
For technical support, troubleshooting assistance beyond this manual, or service inquiries, please contact FrSky customer support through their official website or authorized service centers. Always provide your product model and serial number when seeking support.
Documents and downloads
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.