AIRAM Cosmo Tilt IP20 5.8W/830 Dim WH Recessed LED Spot

1. Introduction

Thank you for choosing the AIRAM Cosmo Tilt IP20 5.8W/830 Dim WH Recessed LED Spot. This manual provides important instructions for the safe and efficient installation, operation, and maintenance of your new LED luminaire. Please read this manual thoroughly before installation and retain it for future reference.

2. Safety Information

To prevent personal injury or product damage, always observe the following safety precautions:

• Electrical Safety: Installation should only be performed by a qualified electrician in accordance with all local and national electrical codes. Ensure the power supply is disconnected at the main circuit breaker before commencing any installation or maintenance work.
• Voltage Compatibility: Verify that the supply voltage matches the requirements specified on the product label.
• Indoor Use Only: This product has an IP20 rating, indicating it is protected against solid objects larger than 12.5mm but has no protection against water. It is designed for indoor use in dry environments only. Do not install in bathrooms, kitchens, or other areas where it may be exposed to moisture.
• Heat Dissipation: Ensure adequate ventilation around the luminaire to prevent overheating. Do not cover the luminaire with insulating material unless specifically designed for it.
• Handling: Handle the LED spot with care. Avoid dropping or subjecting it to strong impacts.
• Dimming: Use only compatible dimmers designed for LED luminaires. Incompatible dimmers may cause flickering or damage to the product.

3. Product Overview

The AIRAM Cosmo Tilt Recessed LED Spot is a high-quality, dimmable lighting solution designed for various indoor applications, such as living rooms. It features a tiltable design, allowing for adjustable light direction.

Figure 3.1: Front view of the AIRAM Cosmo Tilt Recessed LED Spot. This image shows the white housing and the clear, faceted lens covering the LED light source.

Figure 3.2: Angled front view of the AIRAM Cosmo Tilt Recessed LED Spot, highlighting its compact design and the tiltable light element.

Package Contents:

• 1 x AIRAM Cosmo Tilt Recessed LED Spot (Model: 4107168)
• 1 x LED Driver (integrated or separate, as shown in installation images)
• Instruction Manual (this document)

4. Setup and Installation

Important: Ensure power is disconnected at the main circuit breaker before beginning installation.

Required Tools (not supplied):

• Hole saw (for ceiling cut-out)
• Wire strippers
• Screwdriver
• Voltage tester

Installation Steps:

1. Prepare the Ceiling: Choose a suitable location for the LED spot. Using a hole saw, cut a circular opening in the ceiling with a diameter of approximately 80mm. Ensure there is sufficient clearance above the ceiling for the luminaire and its driver.
2. Connect Wiring: Carefully pull the electrical wires from the ceiling opening. Connect the LED spot's driver wires to your mains electrical supply (Live and Neutral) according to local wiring regulations. Ensure all connections are secure and properly insulated.


Figure 4.1: Side view of the AIRAM Cosmo Tilt LED spot showing the connection between the luminaire and its external driver unit via red and black wires.

3. Secure the Luminaire: Fold back the spring clips on the sides of the LED spot. Insert the luminaire into the prepared ceiling opening. The spring clips will automatically expand and hold the luminaire securely in place against the ceiling.


Figure 4.2: Rear view of the AIRAM Cosmo Tilt LED spot, illustrating the spring clips used for secure ceiling mounting and the wiring terminals on the driver.

4. Restore Power: Once the installation is complete and all connections are checked, restore power at the main circuit breaker.
5. Test Functionality: Turn on the light switch to verify the LED spot is working correctly.

Figure 4.3: An example of multiple AIRAM Cosmo Tilt LED spots installed in a staircase ceiling, demonstrating their aesthetic integration and lighting effect.

5. Operating Instructions

The AIRAM Cosmo Tilt LED Spot is designed for simple operation.

• Turning On/Off: Use a standard wall switch connected to the luminaire to turn the light on or off.
• Dimming: If connected to a compatible dimmer switch, you can adjust the brightness of the LED spot by operating the dimmer control. Ensure the dimmer is suitable for LED loads.
• Tilting Function: The light source can be manually tilted to direct the light beam as desired. Gently adjust the inner ring of the luminaire to achieve the desired angle.

6. Maintenance

The AIRAM Cosmo Tilt LED Spot requires minimal maintenance.

• Cleaning: Disconnect power before cleaning. Use a soft, dry, or slightly damp cloth to wipe the surface of the luminaire. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or electrical components.
• No User-Serviceable Parts: The LED light source is integrated and not replaceable by the user. Do not attempt to open or repair the luminaire. If the product malfunctions, contact qualified service personnel.

7. Troubleshooting

If you encounter issues with your AIRAM Cosmo Tilt LED Spot, refer to the following common problems and solutions:

If troubleshooting steps do not resolve the issue, contact AIRAM customer support or a qualified electrician.

8. Specifications

Figure 8.1: Photometric diagram illustrating the light distribution curve for the AIRAM Cosmo Tilt LED spot (Model 4107168).

Figure 8.2: Detailed energy label for the AIRAM Cosmo Tilt LED spot, showing energy class G and 6 kWh/1000h consumption. For more information, visit the EPREL database.

9. Warranty and Support

The AIRAM Cosmo Tilt LED Spot comes with a 3-year warranty, as indicated on the product packaging. This warranty covers defects in materials and workmanship under normal use.

For warranty claims, technical support, or further inquiries, please contact your retailer or AIRAM customer service. Please have your proof of purchase and product model number (4107168) ready when contacting support.