1. Introduction
This manual provides comprehensive instructions for the Fluke Networks DSX-PC6 Single Patch Cord Adapter. This adapter is specifically designed for use with Fluke Networks DSX series cable analyzers to facilitate the testing and certification of Cat 6 Modular Plug Terminated Links (MPTL).
Figure 1: The Fluke Networks DSX-PC6 Single Patch Cord Adapter. This compact blue adapter features an RJ45 port for connecting network cables and is labeled with its model number and purpose.
2. What's in the Box
The standard package for the Fluke Networks DSX-PC6 includes the following item:
- SINGLE DSX CAT 6 ADAPTERS WITH SHIELDED CAT 6 PATCH CORD JACKS
3. Key Features
The DSX-PC6 adapter offers several key features designed for efficient and accurate cable testing:
- Shielded Cat 6 Jack: Ensures reliable and accurate testing of Cat 6 cabling.
- Compatibility: Fully compatible with Fluke Networks DSX series modules, including the DSX-8000.
- MPTL Certification: Designed to be paired with a DSX Permanent Link adapter to perform comprehensive Modular Plug Terminated Link (MPTL) certification.
4. Setup
Proper setup of the DSX-PC6 adapter is crucial for accurate testing. Follow these steps to connect the adapter to your DSX series module:
- Power Off DSX Module: Before connecting the adapter, ensure your Fluke Networks DSX series module (e.g., DSX-8000) is powered off to prevent any potential damage.
- Connect Adapter: Securely connect the DSX-PC6 Single Patch Cord Adapter to the designated port on your DSX series module. Consult your DSX series module's user manual for specific port locations and connection procedures.
- Power On: Once the adapter is firmly connected, power on your DSX series module. The system should automatically detect and recognize the connected adapter.
5. Operating Instructions
The DSX-PC6 adapter is used in conjunction with a DSX Permanent Link adapter to perform MPTL certification. Follow these steps for operation:
- Connect MPTL to DSX-PC6: Connect one end of the Cat 6 Modular Plug Terminated Link (the patch cord end) to the RJ45 port on the DSX-PC6 adapter.
- Connect Other End to Permanent Link Adapter: Connect the other end of the MPTL (the permanent link end) to a DSX Permanent Link adapter. This Permanent Link adapter should then be connected to the second port of your DSX series module.
- Initiate Test: Follow the on-screen prompts and instructions on your DSX series module to select and initiate the MPTL certification test.
- Review Results: Once the test is complete, review the detailed test results displayed on the DSX series module.
6. Maintenance
To ensure the longevity and optimal performance of your DSX-PC6 adapter, adhere to the following maintenance guidelines:
- Cleaning: Keep the adapter clean and free from dust, dirt, and debris. Use a soft, dry, lint-free cloth for cleaning. Do not use abrasive cleaners or solvents.
- Environmental Conditions: Avoid exposing the adapter to extreme temperatures, high humidity, or direct sunlight. Store it in a cool, dry place.
- Physical Inspection: Periodically inspect the RJ45 port and the adapter's casing for any signs of damage, wear, or corrosion.
- Storage: When not in use, store the adapter in its original packaging or a protective case to prevent physical damage.
7. Troubleshooting
If you encounter issues with your DSX-PC6 adapter, refer to the table below for common problems and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Adapter not recognized by DSX module. | Loose connection; DSX module firmware outdated. | Ensure the adapter is securely connected to the DSX module. Power cycle the DSX module. Check the Fluke Networks website for the latest firmware updates for your DSX module and install if available. |
| MPTL test fails or shows errors. | Incorrect setup; faulty patch cord; issue with the link being tested. | Verify all connections are correct as per the operating instructions. Test with a known good patch cord. Inspect the MPTL for physical damage or improper termination. Ensure the correct test limits are selected on the DSX module. |
8. Specifications
Key technical specifications for the Fluke Networks DSX-PC6 Single Patch Cord Adapter:
- Product Dimensions: 6 x 7 x 11 inches (L x W x H)
- Item Weight: 11.68 ounces
- Item Model Number: DSX-PC6
- Manufacturer: FLUKE ELECTRONICS CORPORATION
- Compatible Devices: Fluke Networks DSX series modules, including DSX-8000
- Specific Uses For Product: Professional cable testing and certification of Modular Plug Terminated Links (MPTL)
- Connector Type: RJ45
- Color: Blue
9. Warranty and Support
For detailed information regarding product warranty, technical support, and service, please refer to the official Fluke Networks resources.
Official Fluke Networks Website: www.flukenetworks.com
Customer Support: Contact information for technical assistance and customer service can be found on the official Fluke Networks website.
