Dyna-Glo 18K BTU Grab N Go XL Portable Propane Heater Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your Dyna-Glo 18K BTU Grab N Go XL Portable Propane Heater. Please read all instructions carefully before use and retain this manual for future reference.

The Dyna-Glo Grab N Go XL is designed to provide portable heat for outdoor and emergency indoor situations. It can operate using one or two 1 lb disposable propane cylinders or connect to a 20 lb refillable tank with an optional extension hose (sold separately).

2. Safety Information

WARNING: Failure to follow these instructions can result in fire, explosion, carbon monoxide poisoning, or death.

• Ventilation: Always ensure adequate ventilation when operating this heater. Do not use in unventilated areas.
• Carbon Monoxide: This heater produces carbon monoxide, which is an odorless, colorless gas that can cause death. Install carbon monoxide detectors in all enclosed spaces where the heater is used.
• Clearances: Maintain minimum clearances from combustible materials as specified in the product labeling.
• Fuel: Use only propane gas. Do not use other fuels.
• Children and Pets: Keep children and pets away from the heater during operation.
• Outdoor Use: When using outdoors, ensure the heater is on a stable, level surface.
• Indoor Emergency Use: For emergency indoor use, ensure proper ventilation and never leave unattended.
• Storage: Store propane cylinders in a well-ventilated area, away from heat sources and direct sunlight.

3. Package Contents

Verify that all components are present before assembly and operation.

• Dyna-Glo 18K BTU Grab N Go XL Portable Propane Heater (Model: HA18G)

Note: Propane cylinders (1 lb or 20 lb) and the optional extension hose for 20 lb tanks are sold separately and are not included with the heater.

4. Setup

4.1 Connecting 1 lb Propane Cylinders

1. Ensure the heater's control knob is in the 'OFF' position.
2. Open the side covers of the heater.
3. Screw one or two 1 lb propane cylinders into the swivel valves located inside the side compartments. Hand-tighten only. Do not overtighten.
4. Close the side covers.

Image: Rear view of the heater showing the compartments for 1 lb propane cylinders.

4.2 Connecting to a 20 lb Propane Tank (Optional)

1. Ensure the heater's control knob is in the 'OFF' position.
2. Connect the optional extension hose (sold separately) to the heater's propane inlet.
3. Connect the other end of the extension hose to a 20 lb refillable propane tank.
4. Ensure all connections are tight. Check for leaks using a soapy water solution. Bubbles indicate a leak.

5. Operating Instructions

5.1 Ignition

1. Ensure propane cylinders are securely connected or the 20 lb tank valve is open.
2. Push and gently turn the control knob counter-clockwise to the 'PILOT' position.
3. Hold the knob in for 30-60 seconds to allow gas to flow and the thermocouple to heat up.
4. While still holding the knob in, press the Piezo igniter button repeatedly until the pilot flame ignites. You should see a small flame.
5. Once the pilot is lit, continue to hold the knob in for another 30 seconds, then slowly release it. The pilot flame should remain lit. If it extinguishes, repeat the ignition process.

5.2 Adjusting Heat Settings

Image: Front view of the heater showing the radiant burner.

The Dyna-Glo Grab N Go XL features three heat settings:

1. Low (Setting 1): After the pilot is lit, gently push and turn the control knob counter-clockwise to the 'LOW' position. One ceramic burner will activate, providing approximately 6,000 BTU/hr.
2. Medium (Setting 2): Gently push and turn the control knob counter-clockwise to the 'MEDIUM' position. One ceramic burner will remain active, providing approximately 12,000 BTU/hr.
3. High (Setting 3): Gently push and turn the control knob counter-clockwise to the 'HIGH' position. Both ceramic burners will activate, providing up to 18,000 BTU/hr.

5.3 Shutting Down the Heater

1. Turn the control knob clockwise to the 'OFF' position.
2. If using 1 lb cylinders, disconnect them when the heater is not in use.
3. If using a 20 lb tank, close the valve on the tank.
4. Allow the heater to cool completely before moving or storing.

6. Maintenance

6.1 Cleaning

• Ensure the heater is off and completely cool before cleaning.
• Wipe exterior surfaces with a damp cloth. Do not use abrasive cleaners or solvents.
• Keep the burner and pilot assembly free of dust and debris. Use compressed air if necessary.

6.2 Storage

• Store the heater in a dry, well-ventilated area when not in use.
• Disconnect and remove propane cylinders before storage.

7. Troubleshooting

8. Specifications

Image: Heater dimensions for reference.

• Brand: Dyna-Glo
• Model: HA18G
• Fuel Type: Propane
• Heat Output: Up to 18,000 BTU/hr
• Heating Coverage: Up to 250 sq. ft.
• Ignition Type: Piezo Ignition
• Indoor/Outdoor Usage: Indoor (Emergency), Outdoor
• Product Dimensions: 19.09"D x 9.17"W x 16.46"H
• Item Weight: 10.2 pounds
• Safety Certifications: CSA certified
• UPC: 872076046219

9. Warranty and Support

For warranty information and customer support, please refer to the documentation included with your purchase or visit the official Dyna-Glo website. Keep your purchase receipt for warranty claims.