Lomography Lomo'Instant Wide Camera & Lenses User Manual

1. Safety Instructions

Please read these safety instructions carefully before using your Lomography Lomo'Instant Wide camera. Keep this manual for future reference.

• Do not expose the camera to extreme temperatures, direct sunlight for prolonged periods, or high humidity.
• Avoid dropping the camera or subjecting it to strong impacts.
• Keep the camera and film away from strong magnetic fields.
• Do not attempt to disassemble or modify the camera. Repairs should only be performed by authorized service personnel.
• Keep batteries out of reach of children. If swallowed, seek immediate medical attention.
• Dispose of used batteries and film cartridges according to local regulations.
• The flash can be bright; avoid pointing it directly into eyes at close range.

2. Package Contents

Verify that all items listed below are included in your package:

• Lomography Lomo'Instant Wide Camera (Monte Carlo Black Leather Edition)
• Lomo'Instant Wide Ultra-wide Lens Attachment
• Lomo'Instant Wide Close-up Lens Attachment
• Lomo'Instant Wide Splitzer Lens Attachment
• Colored Gel Flash Filters (Red, Blue, Yellow, Purple)
• Remote Control Shutter Release
• Lens Cap
• Instruction Manual

Image 2.1: The Lomo'Instant Wide camera and its accessories, including the three lens attachments, colored gel filters, and instruction manual, as they appear when unboxed.

3. Camera Overview

Familiarize yourself with the main components of your Lomo'Instant Wide camera.

Image 3.1: Front view of the Lomo'Instant Wide camera, showing the lens, flash, and viewfinder.

Image 3.2: Back view of the Lomo'Instant Wide camera, displaying the film door, exposure compensation dial, and mode selector.

Key Components:

• Lens: The primary lens for capturing images.
• Flash: Provides illumination in low-light conditions.
• Viewfinder: Used to compose your shots.
• Shutter Button: Activates the camera to take a photo.
• Film Ejection Slot: Where developed photos emerge.
• Film Door: Access point for loading and unloading film.
• Exposure Compensation Dial: Adjusts exposure (+1, 0, -1).
• Mode Selector: Switches between shooting modes (Auto, Bulb, Multiple Exposure).
• Battery Compartment: Holds the camera batteries.

4. Setup

4.1 Battery Installation

The Lomo'Instant Wide camera requires four AA batteries (not included). Ensure correct polarity when inserting.

1. Locate the battery compartment cover, typically on the side or bottom of the camera.
2. Open the cover and insert four AA batteries, matching the positive (+) and negative (-) terminals as indicated.
3. Close the battery compartment cover securely.

4.2 Film Loading

The camera uses Fujifilm Instax Wide instant film.

1. Ensure the camera is powered off.
2. Open the film door on the back of the camera.
3. Align the yellow mark on the film cartridge with the yellow mark inside the camera's film compartment.
4. Insert the film cartridge firmly until it clicks into place. Do not press on the black film surface.
5. Close the film door. The camera will automatically eject the dark protective cover.
6. The film counter will display "10" (or the number of exposures in the pack).

Image 4.1: Proper technique for loading an Instax Wide film cartridge into the camera's film compartment.

4.3 Lens Attachment

The Lomo'Instant Wide comes with three interchangeable lens attachments:

• Ultra-wide Lens: For expansive landscapes and group shots.
• Close-up Lens: For detailed macro photography.
• Splitzer Lens: For creative multi-exposure effects.

To attach a lens:

1. Align the attachment lens with the camera's main lens.
2. Gently twist the attachment clockwise until it locks into place.
3. To remove, twist counter-clockwise and pull off.

Image 4.2: The Lomo'Instant Wide camera displayed alongside its three specialized lens attachments and colored flash gels.

5. Operating the Camera

5.1 Power On/Off

To power on the camera, slide the power switch to the "ON" position. To power off, slide it to "OFF".

5.2 Shooting Modes

The Lomo'Instant Wide offers several shooting modes for creative control:

• Auto Mode (A): The camera automatically determines the optimal shutter speed and flash output based on ambient light. This is the recommended mode for most situations.
• Bulb Mode (B): The shutter remains open for as long as the shutter button is pressed (up to a maximum of 30 seconds), allowing for long exposures in low light or for light painting.
• Multiple Exposure Mode (MX): Allows you to take multiple shots on a single frame of film. Press the shutter button for each exposure, then press the MX button again to eject the film.

Use the mode selector switch on the back of the camera to choose your desired mode.

5.3 Exposure Compensation

Adjust the exposure compensation dial to fine-tune the brightness of your photos:

• +1: Makes the photo brighter. Useful for backlit subjects or when you want a slightly overexposed look.
• 0: Standard exposure.
• -1: Makes the photo darker. Useful for bright scenes or when you want a slightly underexposed look.

5.4 Flash Usage and Colored Gels

The built-in flash activates automatically in Auto mode when needed. You can also manually override it. To add creative color effects, slide one of the colored gel filters (red, blue, yellow, purple) into the flash slot.

5.5 Focusing

The Lomo'Instant Wide features zone focusing. Rotate the lens barrel to select the appropriate focus zone:

• 0.6m (2 ft): For close-up subjects.
• 1-2m (3-6 ft): For portraits and small groups.
• Infinity (∞): For landscapes and distant subjects.

When using the Close-up lens attachment, ensure the camera's main lens is set to the closest focus distance (0.6m).

5.6 Taking a Photo

1. Power on the camera.
2. Select your desired shooting mode (Auto, Bulb, or Multiple Exposure).
3. Adjust exposure compensation if necessary.
4. Compose your shot through the viewfinder.
5. Set the focus zone on the lens barrel.
6. Press the shutter button firmly. The photo will eject from the film slot.
7. Allow the photo to develop for a few minutes without shaking or bending it.

Image 5.1: A user holding the Lomo'Instant Wide camera, with a recently developed instant photograph visible on a table.

6. Maintenance

6.1 Cleaning

• Use a soft, dry, lint-free cloth to clean the camera body.
• For the lens, use a specialized lens cleaning cloth and lens cleaning solution. Avoid touching the lens surface with your fingers.
• Do not use abrasive cleaners or solvents on any part of the camera.

6.2 Storage

• When not in use, store the camera in a cool, dry place, away from direct sunlight and dust.
• Remove batteries if the camera will not be used for an extended period to prevent leakage.
• Keep the lens cap on to protect the lens from scratches and dust.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For warranty information and customer support, please refer to the official Lomography website or contact your local dealer. Keep your proof of purchase for warranty claims.

Online resources and FAQs may be available on the manufacturer's website: www.lomography.com