PARKSIDE PSBSA 20 LI C3

Download PDF
Contents

PARKSIDE 20V 3-in-1 Cordless Impact Drill PSBSA 20 LI C3 User Manual

Model: PSBSA 20 LI C3

1. Introduction

This manual provides essential information for the safe and effective operation, setup, and maintenance of your PARKSIDE 20V 3-in-1 Cordless Impact Drill, model PSBSA 20 LI C3. This tool is designed for drilling, screwdriving, and impact drilling in various materials. Please read these instructions thoroughly before first use and keep them for future reference.

Note: The battery and charger are not included with this product and must be purchased separately. This tool is compatible with batteries from the "PARKSIDE X 20V Team" series.

2. Safety Instructions

Always observe basic safety precautions to reduce the risk of fire, electric shock, and personal injury. Keep this manual accessible for all users.

  • Work Area Safety: Keep the work area clean and well-lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
  • Electrical Safety: Avoid body contact with earthed or grounded surfaces. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Personal Safety: Always wear eye protection. Use hearing protection when impact drilling. Wear a dust mask if operations create dust. Dress properly; avoid loose clothing or jewelry. Secure long hair.
  • Tool Use and Care: Do not force the power tool. Use the correct power tool for your application. Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Store idle power tools out of the reach of children.
  • Battery Tool Use and Care: Recharge only with the charger specified by the manufacturer. Use power tools only with specifically designated battery packs.

3. Product Overview

Familiarize yourself with the components of your PARKSIDE 20V 3-in-1 Cordless Impact Drill.

PARKSIDE 20V 3-in-1 Cordless Impact Drill

Image of the PARKSIDE 20V 3-in-1 Cordless Impact Drill without the auxiliary handle attached, showing its compact design.

Side view of PARKSIDE 20V 3-in-1 Cordless Impact Drill

Side view of the PARKSIDE 20V 3-in-1 Cordless Impact Drill, highlighting the chuck, speed selector, and mode switch.

Key Components:

  • Quick-Release Metal Chuck: For easy bit changes (1.5 - 13 mm clamping range).
  • Torque Selector Ring: 20+1 drilling + 1 impact settings for precise control.
  • Mode Selector: Switch between drilling, screwdriving, and impact drilling.
  • 2-Speed Gearbox: Gear 1 (0-440 rpm) for high torque, Gear 2 (0-1650 rpm) for high speed.
  • Variable Speed Trigger: For precise speed control.
  • Rotation Direction Switch: Forward/Reverse.
  • Integrated LED Work Light: Illuminates the work area.
  • Ergonomic Soft Grip: For comfortable handling.
  • Auxiliary Handle: Provides additional control and stability.
  • Magnetic Bit Holder: Convenient storage for bits.
  • Belt Clip: For easy carrying.

4. Setup

4.1 Battery Installation

Ensure the battery is fully charged before use. This tool is compatible with PARKSIDE X 20V Team series batteries (recommended: 20V 2Ah or 4Ah).

  1. Align the battery pack with the battery port on the base of the drill handle.
  2. Slide the battery pack into the port until it clicks securely into place.
  3. To remove, press the release button on the battery pack and slide it out.
PARKSIDE 20V 3-in-1 Cordless Impact Drill with auxiliary handle

The PARKSIDE 20V 3-in-1 Cordless Impact Drill with the auxiliary handle attached. Note: Battery and charger are sold separately.

4.2 Auxiliary Handle Attachment

The auxiliary handle provides improved control, especially during high-torque or impact drilling applications.

  1. Loosen the auxiliary handle by rotating its grip counter-clockwise.
  2. Slide the handle over the chuck and onto the front of the drill body.
  3. Adjust the handle to your desired position (left or right side).
  4. Tighten the handle by rotating its grip clockwise until it is secure.
Top view of drill with auxiliary handle attached

Top-down view of the PARKSIDE 20V 3-in-1 Cordless Impact Drill, showing the auxiliary handle attached and its adjustable positions.

4.3 Bit Installation

Always ensure the drill is switched off and the battery is removed before changing bits.

  1. Rotate the chuck collar counter-clockwise to open the chuck jaws.
  2. Insert the desired drill bit or screwdriver bit into the chuck, ensuring it is centered.
  3. Rotate the chuck collar clockwise to tighten the jaws firmly around the bit. Ensure the bit is securely held.
Close-up of chuck with screwdriver bit

Close-up view of the drill's metal quick-release chuck with a screwdriver bit securely installed, and the auxiliary handle.

5. Operating Instructions

5.1 Selecting Operating Mode

Rotate the mode selector ring to choose one of the three functions:

  • Screwdriving Mode: For driving and removing screws.
  • Drilling Mode: For drilling holes in wood, metal, and plastic.
  • Impact Drilling Mode: For drilling into masonry and concrete (requires appropriate masonry bits).

5.2 Adjusting Torque and Speed

  • Torque Setting (Screwdriving Mode): Rotate the torque selector ring to one of the 20 settings. Lower settings are for smaller screws and softer materials, higher settings for larger screws and harder materials. The clutch will disengage once the set torque is reached, preventing overtightening.
  • Speed Gear Selection: Use the 2-speed gearbox switch located on top of the drill. Gear 1 (low speed, high torque) is suitable for screwdriving and large diameter drilling. Gear 2 (high speed, lower torque) is ideal for small diameter drilling.
  • Variable Speed Trigger: The trigger allows for variable speed control. Press lightly for slower speeds and harder for faster speeds.

5.3 Drilling and Screwdriving

  1. Select the appropriate mode (Drilling or Screwdriving) and adjust torque/speed.
  2. Ensure the rotation direction switch is set to forward (clockwise).
  3. Position the bit on the workpiece.
  4. Start the drill by gently pressing the trigger, gradually increasing speed as needed.
  5. Apply steady, even pressure.
Drill with screwdriver bit and screws

The impact drill configured for screwdriving, with a screwdriver bit inserted into the chuck and screws on the surface.

User drilling into wood

A user operating the PARKSIDE 20V 3-in-1 Cordless Impact Drill to drill into a wooden surface, demonstrating proper handling with the auxiliary handle.

Close-up of drill bit in action

Detailed view of a drill bit penetrating a wooden surface, illustrating the drilling process.

5.4 Impact Drilling

When impact drilling, ensure the auxiliary handle is securely attached and use appropriate masonry drill bits.

  1. Select Impact Drilling mode.
  2. Set the speed to Gear 2 for optimal impact performance.
  3. Apply firm, steady pressure to the drill while pressing the trigger. The impact mechanism will engage automatically.

5.5 LED Work Light

The integrated LED work light automatically illuminates when the trigger is pressed, providing visibility in dimly lit areas.

5.6 Rotation Direction

The rotation direction switch is located above the trigger. Push it left for forward (clockwise) rotation and right for reverse (counter-clockwise) rotation. The center position locks the trigger for safety.

6. Maintenance and Cleaning

Regular maintenance ensures optimal performance and extends the life of your tool.

  • Cleaning: Always disconnect the battery before cleaning. Keep the ventilation openings clean to prevent overheating. Use a soft, damp cloth to clean the tool casing. Do not use harsh chemicals or abrasive cleaners.
  • Chuck Maintenance: Periodically clean the chuck jaws to ensure proper gripping of bits.
  • Storage: Store the tool in a dry, secure place out of reach of children. Remove the battery pack before long-term storage.
  • Battery Care: Store batteries in a cool, dry place. Do not store fully discharged batteries. Recharge them periodically if not in use for extended periods.

7. Troubleshooting

ProblemPossible CauseSolution
Tool does not startBattery not inserted correctly
Battery discharged
Rotation direction switch in center (locked) position
Reinsert battery securely
Charge battery
Move switch to forward or reverse position
Reduced power/performanceBattery low
Incorrect speed/torque setting
Overload
Charge battery
Adjust speed/torque for the task
Reduce pressure, allow tool to cool
Bit slips in chuckChuck not tightened sufficiently
Chuck jaws dirty
Tighten chuck firmly
Clean chuck jaws
Excessive vibrationDamaged or bent bit
Loose auxiliary handle
Replace bit
Tighten auxiliary handle

8. Specifications

FeatureSpecification
Model NumberPSBSA 20 LI C3 (IAN-100370517-3)
BrandPARKSIDE
Power SourceBattery-powered (20V, compatible with PARKSIDE X 20V Team series)
Voltage20 Volts
Max Torque45 Newton-meters
No-Load Speed (Gear 1)0-440 rpm
No-Load Speed (Gear 2)0-1650 rpm
Impact Rate26,400 bpm
Torque Settings20 + 1 drilling + 1 impact
Chuck Clamping Range1.5 - 13 mm
Product Dimensions (L x W x H)30 x 11 x 29 cm
Weight (without battery)2.56 Kilograms
MaterialMetal and Plastic
Included ComponentsAuxiliary handle, 2 bits

9. Warranty and Support

For warranty information, technical support, or to order replacement parts, please refer to the documentation provided with your purchase or contact PARKSIDE customer service. Keep your proof of purchase for warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.