1. Introduction
Thank you for choosing the EMPIRE GAMING Ruby Gaming PC Case. This manual provides detailed instructions for setting up, operating, maintaining, and troubleshooting your new PC case. Please read this manual carefully before installation and keep it for future reference.
Figure 1.1: EMPIRE GAMING Ruby Gaming PC Case (White)
The Ruby Gaming PC Case is a mid-tower chassis designed for ATX, Micro-ATX, and ITX motherboards. It features a mesh front panel for optimal airflow, an acrylic side panel to showcase your components, and comes equipped with four 120mm addressable RGB (ARGB) fans for vibrant lighting and efficient cooling.
2. Package Contents
Before proceeding with the installation, please verify that all components listed below are present in your package:
- EMPIRE GAMING Ruby PC Case
- 4 x 120mm ARGB Fans (pre-installed)
- Accessory Kit (screws, cable ties, standoffs)
- User Manual (this document)
3. Setup and Installation
3.1 Component Compatibility
The Ruby case offers broad compatibility for various PC components:
- Motherboard Support: ATX, Micro-ATX (mATX), ITX
- CPU Cooler Height: Up to 162 mm
- GPU Length: Up to 320 mm
- Storage: 5 total drive bays (HDD / SSD)
- Radiator Support: 120mm, 240mm, 360mm (front); 120mm (rear); 120mm, 240mm (top)
Figure 3.1: Internal Component Clearance and Motherboard Compatibility
3.2 Installation Steps
- Prepare the Case: Carefully remove the side panels. The acrylic side panel is secured with thumb screws. The opposite metal side panel is secured with standard screws.
- Install Motherboard: Align your ATX, mATX, or ITX motherboard with the standoffs inside the case. Secure it with the provided screws.
- Install Power Supply Unit (PSU): Mount your PSU in the dedicated compartment at the bottom of the case. Secure it with screws.
- Install Storage Drives: Install your 2.5-inch SSDs and 3.5-inch HDDs into the designated drive bays.
- Install Graphics Card (GPU): Insert your graphics card into the appropriate PCIe slot on your motherboard and secure it with the retention clip and screws.
- Install CPU Cooler: If not already installed, mount your CPU cooler (air or liquid) ensuring it fits within the 162mm height clearance.
- Connect Front Panel Cables: Connect the front panel I/O cables (USB 2.0, USB 3.0, HD Audio, Power, Reset, LED) to their respective headers on your motherboard.
- Cable Management: Utilize the cable routing cutouts and tie-down points behind the motherboard tray to manage cables for a clean build and improved airflow.
- Close the Case: Once all components are installed and cables are managed, reattach the side panels.
Figure 3.2: Front Panel Connectivity
4. Operating Instructions
4.1 Power On/Off
Press the power button located on the top panel of the case to turn on your PC. To turn off, use the shutdown option in your operating system or press and hold the power button for a few seconds.
4.2 ARGB Fan Control
The EMPIRE GAMING Ruby case includes four 120mm Addressable RGB (ARGB) fans. These fans are connected to an integrated controller hub. You have two primary methods to control the RGB lighting:
- LED Button Control: Use the dedicated LED button on the top panel of the case to cycle through over 20 pre-set RGB effects and colors.
- Motherboard Synchronization (MB Sync): The integrated controller is compatible with popular motherboard RGB synchronization technologies via a 3-pin 5V ARGB header. Connect the controller to your motherboard's ARGB header to control lighting through software such as:
- ASUS Aura Sync
- GIGABYTE RGB Fusion
- MSI Mystic Light Sync
- ASRock Polychrome Sync
Figure 4.1: ARGB Fan and Motherboard Sync Compatibility
4.3 Airflow Configuration
The pre-installed fans are configured for optimal airflow, with front fans acting as intake and the rear fan as exhaust. This creates a positive pressure system, helping to keep dust out.
Figure 4.2: Recommended Airflow Pattern
5. Maintenance
5.1 Dust Filter Cleaning
The EMPIRE GAMING Ruby case is equipped with dust filters to prevent dust buildup inside your system. Regularly clean these filters to maintain optimal airflow and cooling performance.
- Front Panel Filter: The mesh front panel acts as a dust filter. It can be carefully removed for cleaning.
- Top Panel Filter: A magnetic dust filter is located on the top panel. Simply lift it off for cleaning.
- PSU Filter: A removable dust filter is located at the bottom, beneath the power supply unit.
To clean, gently brush off accumulated dust or rinse with water if heavily soiled. Ensure filters are completely dry before reattaching.
Figure 5.1: Dust Filter Detail
5.2 General Cleaning
Use a soft, dry cloth to wipe down the exterior of the case. For stubborn marks, a slightly damp cloth can be used. Avoid abrasive cleaners or solvents that may damage the finish or acrylic panel.
6. Troubleshooting
This section addresses common issues you might encounter with your PC case.
- Fans Not Spinning/RGB Not Lighting Up:
- Check all fan and RGB cables are securely connected to the integrated controller and the controller is powered.
- If using motherboard sync, ensure the 3-pin 5V ARGB cable is correctly connected to the motherboard's ARGB header and the motherboard's RGB software is installed and configured.
- Verify that the power supply is providing adequate power to all components.
- Front Panel USB Ports Not Working:
- Ensure the USB 2.0 and USB 3.0 headers from the front panel are correctly plugged into the corresponding headers on your motherboard.
- Check your motherboard's BIOS settings to ensure USB ports are enabled.
- Power Button Not Responding:
- Confirm the power button cable from the front panel is correctly connected to the 'PWR SW' pins on your motherboard.
- Ensure your power supply unit is switched on and functioning correctly.
7. Specifications
Detailed technical specifications for the EMPIRE GAMING Ruby Gaming PC Case:
| Feature | Specification |
|---|---|
| Model Number | OE-CA-22WT |
| Case Type | Mid Tower |
| Motherboard Compatibility | ATX, Micro-ATX (mATX), ITX |
| Dimensions (L x W x H) | 390 x 204 x 430 mm (15.3 x 8 x 16.9 inches) |
| Weight | 3.2 Kg |
| Material | Acrylic (side panel), Steel, Mesh |
| Pre-installed Fans | 4 x 120mm ARGB (3 front, 1 rear) |
| Fan Support (Total) | Front: 3x 120mm; Rear: 1x 120mm; Top: 2x 120mm (not included) |
| Radiator Support | Front: 120/240/360mm; Rear: 120mm; Top: 120/240mm |
| CPU Cooler Clearance | Up to 162 mm |
| GPU Length Clearance | Up to 320 mm |
| Drive Bays | 5 (HDD / SSD) |
| Front I/O Ports | 2 x USB 2.0, 1 x USB 3.0, 1 x HD Audio, 1 x LED Button |
| PSU Mounting | Bottom Mount |
Figure 7.1: Case Dimensions
8. Warranty and Support
8.1 Warranty Information
This product is subject to the standard return and replacement policies of the retailer. For specific warranty terms and conditions, please refer to your purchase documentation or contact your point of sale. Typically, a 30-day refund/replacement period is offered.
8.2 Customer Support
For technical assistance, troubleshooting, or inquiries regarding your EMPIRE GAMING Ruby PC Case, please visit the official EMPIRE GAMING brand store or contact their customer support channels. You can find more information at the EMPIRE GAMING Store on Amazon.
