Okin JLDQ.11.156.333D Power Recliner Motor Instruction Manual

1. Introduction and Overview

The Okin JLDQ.11.156.333D is a power recliner motor designed as a replacement actuator for various lift chairs and recliners. This motor is part of the original Okin JLDQ series and is suitable for replacing models such as JLDQ.11.156.333, JLDQ.11.156.333A, JLDQ.11.156.333K, JLDQ.11.156.333P, and JLDQ.11.156.333Z. While minor differences may exist between these models, they do not affect the motor's functionality or use. Always verify your existing motor's brand and model number before proceeding with replacement.

2. Safety Information

WARNING: Always troubleshoot the switch and power supply first before inspecting the motor. Do not exceed the maximum weight recommendation of 165.34 pounds (750 N push/pull force). This product involves electrical components and moving parts; always follow safety guidelines when handling and installing. Ensure the power supply is disconnected before any installation or maintenance procedures.

3. Product Features and Components

The Okin JLDQ.11.156.333D actuator motor set includes one motor and two connectors. The construction features black PA (polyamide) and silver-white aluminum components for durability.

• 5-pin Round Plug: This connector is for the switch hand control.
• 2-pin Square Plug with Clip: This connector is for the power supply.

Figure 3.1: Connectors for the Okin JLDQ.11.156.333D Power Recliner Motor. The 5-pin round plug connects to the hand control, and the 2-pin square plug with a clip connects to the power supply.

Figure 3.2: Product label for the Okin JLDQ.11.156.333D motor, displaying model information, serial number (e.g., Q22111234 00002), and certifications.

Figure 3.3: The Okin JLDQ.11.156.333D motor, illustrating its application in a recliner chair.

4. Setup and Installation

Installation of the Okin JLDQ.11.156.333D motor is designed to be straightforward. Ensure that the new actuator's minimum install dimension, stroke, and plugs are compatible with your recliner's frame. The motor is typically secured by bolts on the bracket at each end.

1. Disconnect Power: Before beginning, unplug the recliner from the power outlet.
2. Remove Old Motor: Carefully unbolt the old motor from the recliner frame. Disconnect the 5-pin hand control plug and the 2-pin power supply plug.
3. Install New Motor: Position the new Okin JLDQ.11.156.333D motor into the recliner frame. Secure it by bolting the brackets at both ends.
4. Connect Plugs: Connect the 5-pin round plug from the new motor to the hand control. Connect the 2-pin square plug with the clip to the power supply.
5. Test Functionality: Once installed and all connections are secure, plug the recliner back into the power outlet and test the motor's operation using the hand control.

The motor comes with the track system, making it a complete replacement unit. This design simplifies the replacement process.

5. Operation

The Okin JLDQ.11.156.333D power recliner motor operates in conjunction with your recliner's hand control. Pressing the appropriate buttons on the hand control will extend or retract the motor's stroke, allowing the recliner to move into various positions. The motor has an operation frequency of 1 minute ON / 8 minutes OFF, indicating its duty cycle for continuous use.

6. Maintenance

To ensure the longevity and optimal performance of your Okin JLDQ.11.156.333D motor, follow these maintenance guidelines:

• Cleaning: Wipe clean the exterior of the motor and its components with a dry or slightly damp cloth. Avoid using harsh chemicals or abrasive cleaners.
• Inspection: Periodically inspect the motor and its connections for any signs of wear, damage, or loose wiring. Ensure all bolts and fasteners are secure.
• Lubrication: The internal mechanisms are factory-lubricated. Avoid applying external lubricants unless specifically instructed by Okin support.

7. Troubleshooting

If your recliner is not operating correctly, consider the following troubleshooting steps:

• Power Supply: Ensure the recliner is properly plugged into a functioning power outlet. Check the power supply unit for any indicator lights or signs of damage.
• Hand Control: Test the hand control for responsiveness. If the hand control is faulty, the motor will not receive commands.
• Connections: Verify that all plugs (5-pin for hand control, 2-pin for power) are securely connected to the motor and the power supply.
• Motor Compatibility: Confirm that the installed motor is the correct model and compatible with your recliner's frame and electrical system.
• Obstructions: Check for any obstructions that might be preventing the recliner mechanism or motor from moving freely.

If these steps do not resolve the issue, contact customer support for further assistance.

8. Specifications

9. Warranty and Support

For specific warranty information regarding your Okin JLDQ.11.156.333D power recliner motor, please refer to the documentation provided at the time of purchase or contact Okin customer support directly. Keep your purchase receipt as proof of purchase for any warranty claims.

For technical assistance, troubleshooting beyond the scope of this manual, or to inquire about replacement parts, please visit the official Okin website or contact their customer service department. Contact information can typically be found on the product packaging or the manufacturer's website.