1. Introduction
Thank you for choosing the Onforu 65W LED Motion Sensor Outdoor Flood Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before installation and retain them for future reference.
Image 1.1: Two Onforu 65W LED Motion Sensor Outdoor Flood Lights.
2. Important Safety Information
WARNING: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with all local electrical codes and ordinances. Always turn off power at the circuit breaker before installation or servicing.
- Do not connect to a dimmer switch.
- Ensure the power supply is 120V AC, 60Hz.
- Do not attempt to disassemble or modify the fixture.
- Keep flammable materials away from the light fixture.
- Suitable for wet locations. Ensure all connections are properly sealed.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- Onforu 65W LED Motion Sensor Outdoor Flood Light (2 units)
- Mounting Bracket
- Rubber Gasket
- Wire Nuts
- Mounting Screws
- Instruction Manual
4. Product Features
- High Brightness & Energy Efficiency: 6500 Lumens output from 65W LED, equivalent to 450W traditional bulbs.
- Adjustable Design: Three adjustable heads provide a 270-degree detection zone for wide coverage.
- Enhanced Motion Sensor: 180-degree sensing angle, detecting motion up to 72 feet away. Adjustable lighting time from 10 seconds to 7 minutes.
- Durable & Weatherproof: IP65 waterproof and dust-proof rating, made of die-cast aluminum for excellent heat dissipation and long lifespan.
- Color Temperature: 6500K Daylight White for clear, bright illumination.
Image 4.1: Key features of the Onforu LED Motion Sensor Outdoor Flood Light.
Image 4.2: Aluminum construction for efficient heat dissipation.
5. Installation Guide
Before You Begin: Ensure power is OFF at the circuit breaker. Recommended installation height is 8.2-16.4 feet (2.5-5 meters).
5.1 Mounting Options
The fixture can be mounted on a wall or soffit.
Image 5.1: Soffit Mounted vs. Wall Mounted installation examples.
5.2 Wiring Instructions
- Turn off power at the main circuit breaker.
- Attach the mounting bracket to the junction box using the provided screws.
- Connect the wires:
- Black (L): Connect to the live wire from the power supply.
- White (N): Connect to the neutral wire from the power supply.
- Green (GND): Connect to the ground wire from the power supply.
- Ensure the rubber gasket is properly seated between the fixture and the mounting surface to maintain IP65 rating.
- Secure the light fixture to the mounting bracket.
- Adjust the light heads to the desired angles.
- Restore power at the circuit breaker.
Image 5.2: Wiring diagram and product dimensions.
Image 5.3: Visual guide for installation steps.
6. Operating Instructions
The motion sensor has three adjustable knobs for customization:
- SENS (Sensitivity): Adjusts the detection distance. Turn towards '-' for lower sensitivity (up to 10m) or '+' for higher sensitivity (up to 22m/72ft).
- LUX (Ambient Light): Determines when the sensor activates. Turn towards the moon icon for activation only at night (less than 10 LUX). Turn towards the sun icon for activation during both day and night.
- TIME (Time Delay): Sets how long the light stays on after motion is detected. Adjustable from 10 seconds to 7 minutes. Turn towards '-' for shorter duration or '+' for longer duration.
Image 6.1: Motion sensor adjustment knobs for LUX, SENS, and TIME.
7. Maintenance
- Clean the fixture regularly with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Periodically check electrical connections for tightness and signs of wear.
- Ensure the motion sensor lens is clear of dirt, dust, or obstructions for optimal performance.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power; incorrect wiring; LUX setting too low. | Check circuit breaker; verify wiring connections; adjust LUX setting towards 'sun' icon. |
| Light stays on continuously. | Continuous motion detected; TIME setting too long; wiring issue. | Ensure no constant motion in detection area; adjust TIME setting to shorter duration; check wiring (live and neutral might be reversed). |
| Motion sensor not detecting. | SENS setting too low; obstructions; incorrect mounting height. | Adjust SENS setting towards '+'; clear obstructions from sensor view; verify mounting height is within recommended range. |
| Light flickers. | Loose wiring connection; unstable power supply. | Check and tighten all wiring connections; consult an electrician for power supply issues. |
9. Specifications
| Feature | Specification |
|---|---|
| Brand | Onforu |
| Model Number | BDB55G-3 |
| Wattage | 65 Watts |
| Brightness | 6500 Lumens |
| Color Temperature | 6500 Kelvin (Daylight White) |
| Motion Sensor Angle | 180° |
| Motion Detection Distance | Up to 72 feet |
| Time Delay Adjustment | 10 seconds to 7 minutes |
| Water Resistance Level | IP65 Waterproof |
| Material | Metal (Die-cast Aluminum) |
| Voltage | 120 Volts |
| Product Dimensions | 10.7"L x 5.8"W x 4.7"H |
| Number of Light Sources | 3 (Adjustable Heads) |
| Installation Type | Wall Mount |
10. Warranty & Support
This Onforu product comes with a Limited Warranty. For specific details regarding the warranty period and coverage, please refer to the warranty information provided with your purchase or contact Onforu customer support.
For technical support, troubleshooting assistance, or any inquiries, please contact Onforu customer service through the retailer's platform or visit the official Onforu website.
