Introduction
This manual provides instructions for the VINABTY RC-682M replacement remote control, designed for use with a wide range of ONKYO Audio Video Systems. This remote functions as a direct replacement and does not require any programming or pairing. Simply insert batteries to begin operation.
Setup
Battery Installation
The VINABTY RC-682M remote control requires two (2) AAA alkaline batteries for operation. Follow these steps to install the batteries:
- Locate the battery compartment on the back of the remote control.
- Slide the battery compartment cover downwards or outwards to open it.
- Insert two new AAA alkaline batteries, ensuring that the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
The remote is now ready for use. No additional programming or pairing is required.
Figure 1: Top-down view of the VINABTY RC-682M remote control, displaying all buttons and their labels.
Operating Instructions
The VINABTY RC-682M is an infrared remote control. For optimal performance, point the remote directly at the infrared receiver of your ONKYO Audio Video System. Ensure there are no obstructions between the remote and the system.
Key Functions Overview
- STANDBY/ON (I/O): Powers the ONKYO system on or off.
- INPUT SELECTOR (1-9, 0, +10, -/--): Selects various input sources such as VCR/DVR, CBL/SAT, GAME/TV, AUX, MULTI CH, DVD, CD, TUNER, TAPE, MD/CDR, DOCK, TV, VCR, CABLE, SAT.
- VOL (+/-): Adjusts the master volume level.
- Muting: Mutes or unmutes the audio output.
- Navigation Pad (Up, Down, Left, Right, ENTER): Used for menu navigation and selection.
- SETUP: Accesses the system setup menu.
- PLAY/PAUSE, STOP, FAST FORWARD, REWIND, SKIP (Previous/Next): Standard playback controls for compatible devices.
- LISTENING MODE (STEREO, SURROUND): Selects different audio listening modes.
- DISPLAY: Toggles display information on the connected device.
- DIMMER: Adjusts the brightness of the system's display.
Figure 2: Angled view of the remote control, highlighting the input selector and volume controls.
Compatible ONKYO Audio Video System Models
This remote control is compatible with the following ONKYO Audio Video System models:
- 24140681, DTR5.8, DTR58, DTR7.2
- HTR330, HTR340, HTR340S, HTR508, HTR530, HTR540, HTR550, HTR550S, HTR557, HTR640, HTR940
- HTS3100, HTS3100S, HTS530, HTS590, HTS590S, HTS680, HTS780, HTS787C, HTS790, HTS790S, HTS894, HTS907, HTS990THX, HTSP904, HTSP908, HTSR600, HTSR600S, HTSR750, HTSR800, HTSR800S
- OVD2744, TX8555, TXSA605, TXSA8560
- TXSR303E, TXSR305B, TXSR307, TXSR503, TXSR503B, TXSR503S, TXSR504, TXSR504E, TXSR505, TXSR505E, TXSR505S, TXSR574, TXSR574S, TXSR575, TXSR575S
- TXSR604, TXSR604E, TXSR605, TXSR605S, TXSR674, TXSR674E, TXSR703, TXSR703S, TXSR803, TXSR803S, TXSR804, TXSR804E, TXSR804S
- TXSR8450, TXSR8460, TXSR8467, TXSR8550
Maintenance
Cleaning the Remote
To maintain the remote control's appearance and functionality, clean it regularly:
- Use a soft, dry cloth to wipe the surface of the remote.
- For stubborn dirt, slightly dampen the cloth with water, then wipe dry immediately.
- Avoid using abrasive cleaners, solvents, or chemical sprays, as these can damage the remote's finish or internal components.
Battery Replacement
Replace the batteries when the remote's response becomes sluggish, inconsistent, or stops working entirely. Always replace both AAA batteries simultaneously with new alkaline batteries. Do not mix old and new batteries, or different types of batteries.
Storage
When not in use for extended periods, store the remote control in a dry place, away from direct sunlight, high temperatures, and excessive humidity. Remove batteries if storing for several months to prevent leakage.
Troubleshooting
If you encounter issues with your VINABTY RC-682M remote control, refer to the following troubleshooting tips:
- Remote not responding:
- Check if the batteries are installed correctly with the correct polarity.
- Replace the batteries with new AAA alkaline batteries.
- Ensure there are no obstructions between the remote control and the ONKYO system's infrared receiver.
- Point the remote directly at the ONKYO system.
- Limited operating range:
- Ensure batteries are fresh and fully charged.
- Remove any potential sources of infrared interference (e.g., strong light sources, other electronic devices).
- Specific buttons not working:
- Clean the remote control, especially around the problematic buttons, to ensure no dirt or debris is interfering.
- Verify that the ONKYO system is powered on and functioning correctly.
If the issue persists after trying these steps, please refer to the Support section.
Specifications
| Model Number | YK-RC682M-DPLC-GB |
| Brand | VINABTY |
| Connectivity Technology | Infrared |
| Controller Type | Button Control |
| Batteries Required | 2 x AAA Alkaline Batteries |
| Maximum Range | 10 Meters |
| Product Dimensions (L x W x H) | 15L x 8W x 0.8H centimeters |
| Special Feature | Ergonomic Design |
| Maximum Supported Devices | 18 (for various ONKYO Audio Video Systems) |
Warranty
Specific warranty information for the VINABTY RC-682M remote control is not provided in the product details. For details regarding warranty coverage, duration, and claims, please contact the seller, Remote-Europe-Store, directly through your purchase platform.
Support
For any questions, technical assistance, or further support regarding your VINABTY RC-682M remote control, please contact the seller, Remote-Europe-Store. They can provide guidance on product usage, compatibility, and troubleshooting beyond the scope of this manual.
You can typically find the seller's contact information on your order details page or through the product listing on the platform where you made your purchase.