Edimax GP-103IT IEEE 802.3bt Gigabit 90W PoE++ Injector User Manual

1. Introduction

The Edimax GP-103IT is an IEEE 802.3bt Gigabit 90W Power over Ethernet Plus Plus (PoE++) Injector designed to provide both data and power to PoE-compatible devices over a single Ethernet cable. This device is ideal for extending network reach to devices such as high-power wireless access points, IP cameras, and VoIP phones in locations where power outlets are not readily available.

It simplifies network deployment by eliminating the need for separate power cables for PoE-enabled devices, offering a flexible and cost-effective solution for various network applications.

2. Product Features

• IEEE 802.3bt Standard Compliance: Supports the latest PoE++ standard, delivering up to 90W of power.
• Gigabit Ethernet Speed: Provides high-speed data transmission at 1000Mbps for demanding network applications.
• Single Cable Solution: Integrates power and data transmission over a single Ethernet cable, simplifying installation.
• Plug and Play: Easy to install with no software configuration required.
• Flexible Deployment: Supports both desktop placement and wall-mounting options.
• Robust Design: Features a durable painted exterior finish.
• Safety Compliance: Meets CE and FCC specifications.

3. Hardware Overview

Familiarize yourself with the components and indicators of the GP-103IT PoE++ Injector.

Figure 3.1: Front View of GP-103IT

This image displays the front panel of the Edimax GP-103IT injector, highlighting the two RJ-45 ports labeled "DATA IN" and "PoE/DATA OUT," along with the "PWR" and "PoE" LED indicators.

Figure 3.2: Rear View of GP-103IT

This image shows the rear panel of the Edimax GP-103IT, featuring the AC power input connector and product information labels.

3.1 Front Panel Description

• PWR LED:
  • Green: The device is powered on and operating normally.
  • Off: The device is not receiving power.
• PoE LED:
  • Green: Power over Ethernet (PoE) is active and supplying power to a connected Powered Device (PD).
  • Off: PoE is not active or no PD is connected.
• DATA IN Port (RJ-45): Connects to your network switch, router, or other non-PoE network device. This port receives data only.
• PoE/DATA OUT Port (RJ-45): Connects to your PoE-compatible Powered Device (PD), such as an IP camera, wireless access point, or VoIP phone. This port transmits both data and power.

3.2 Rear Panel Description

• AC INPUT (100-240VAC 50/60Hz 1.5A MAX): Connect the provided AC power cord to this input to power the injector.

4. Setup and Installation

Follow these steps to set up your Edimax GP-103IT PoE++ Injector.

4.1 Connecting the Injector

1. Power Connection: Connect the AC power cord to the "AC INPUT" port on the rear of the GP-103IT and then plug the other end into a standard electrical outlet. The "PWR" LED on the front panel should illuminate green.
2. Data Input Connection: Connect an Ethernet cable from your network switch, router, or other non-PoE network device to the "DATA IN" port on the front of the GP-103IT.
3. PoE Output Connection: Connect another Ethernet cable from the "PoE/DATA OUT" port on the front of the GP-103IT to your PoE-compatible Powered Device (PD). Ensure the PD is compliant with IEEE 802.3bt or earlier PoE standards (802.3af/at) that can be powered by this injector.
4. Verify Connection: Once the PD is connected, the "PoE" LED on the front panel of the GP-103IT should illuminate green, indicating that power is being supplied to the PD.

Figure 4.1: Connection Diagram

This diagram illustrates the high-speed data and power delivery capabilities of the Edimax GP-103IT, showing two Ethernet cables connected to the injector, representing data input and combined data/power output to a device.

4.2 Mounting Options

The GP-103IT offers flexible placement options:

• Desktop Placement: Simply place the injector on a flat, stable surface.
• Wall-Mounting: The injector can be mounted on a wall using screws (not included) through the mounting holes on the bottom of the unit. Ensure the mounting surface is sturdy enough to support the device.

Figure 4.2: Mounting Options

This image demonstrates the two primary installation methods for the GP-103IT: traditional desktop placement and wall-mounting for space efficiency.

5. Operating the Injector

Once properly connected, the Edimax GP-103IT operates automatically. It will detect the connected Powered Device (PD) and supply the necessary power according to the IEEE 802.3bt standard.

• The PWR LED should remain solid green, indicating the injector is powered on.
• The PoE LED should illuminate solid green when a compatible PD is connected and receiving power. If the PoE LED is off, check the connection to the PD and ensure the PD is PoE-compatible.
• Data transmission will occur transparently through the injector between your network and the PD.

6. Maintenance

The Edimax GP-103IT is designed for reliable operation with minimal maintenance. To ensure optimal performance and longevity:

• Keep the device in a cool, dry place, away from direct sunlight, heat sources, and excessive moisture.
• Ensure proper ventilation around the device. Do not block the ventilation holes.
• Clean the exterior of the device with a soft, dry cloth. Do not use liquid or aerosol cleaners.
• Avoid dropping or subjecting the device to strong impacts.

7. Troubleshooting

If you encounter issues with your GP-103IT, refer to the following common problems and solutions:

8. Specifications

9. Warranty and Support

For warranty information and technical support, please refer to the official Edimax website or contact your local Edimax distributor. Keep your purchase receipt for warranty claims.

Edimax Official Website: www.edimax.com

EU Spare Part Availability Duration: 1 Year