1. Safety Information
Read and understand all safety warnings and instructions before operating this heater. Failure to follow these instructions may result in fire, explosion, serious injury, or death. Keep this manual for future reference.
- Ventilation: This heater requires adequate ventilation. Operate only in well-ventilated areas. Do not use in unventilated spaces, basements, or enclosed areas. Ensure a minimum opening of 3 square feet for every 100,000 BTU/hr of heater output.
- Fuel: Use only liquid propane (LP) gas. Do not use natural gas or any other fuel. Connect the heater only to a 20 lb. or larger propane cylinder.
- Clearances: Maintain minimum clearances from combustible materials: 6 feet from the front, 2 feet from the top, 2 feet from the sides, and 2 feet from the rear.
- Electrical: Connect the heater to a properly grounded 120V AC outlet. Do not use extension cords unless absolutely necessary and ensure they are rated for outdoor use and the heater's power requirements.
- Operation: Never leave the heater unattended while operating. Do not move, handle, or service the heater while it is hot or connected to a power source/fuel supply.
- Children and Pets: Keep children and pets away from the heater at all times.
- CSA Certified: This heater is CSA certified, indicating compliance with applicable safety standards.
2. Setup
Follow these steps for initial setup and connection of your BILT HARD Propane Heater.
- Unpacking: Carefully remove the heater from its packaging. Inspect for any shipping damage. Report any damage immediately to the retailer.
- Placement: Place the heater on a level, stable, non-combustible surface. Ensure adequate clearance from all combustible materials as specified in the Safety Information section.
- Connect Propane Tank:
- Ensure the propane tank valve is closed.
- Connect the regulator hose to the propane tank valve. Hand-tighten first, then use a wrench to secure it firmly.
- Connect the other end of the hose to the heater's gas inlet. Ensure all connections are tight to prevent leaks.
- Perform a leak test: Apply a soap and water solution to all gas connections. Open the propane tank valve slowly. If bubbles appear, close the valve immediately and re-tighten connections. Repeat until no bubbles are present.
- Electrical Connection: Plug the heater's power cord into a grounded 120V AC electrical outlet.
3. Operation
Operating your BILT HARD Propane Heater is straightforward. Always ensure proper ventilation during operation.
- Starting the Heater:
- Ensure the heater is properly connected to the propane tank and electrical outlet.
- Slowly open the valve on the propane tank.
- Turn the control knob on the heater to the 'ON' position.
- Press and hold the ignition button until the burner ignites. You should hear a click and see a flame. Release the button once the flame is stable.
- Adjusting Heat Output: The heater features a variable heat output control. Rotate the control knob to adjust the heat intensity from 75,000 BTU to 125,000 BTU.
- Adjusting Heat Angle: The heater's angle can be adjusted to direct heat efficiently. Loosen the side knobs, tilt the heater to the desired angle, and re-tighten the knobs.
- Shutting Down the Heater:
- Turn the control knob on the heater to the 'OFF' position.
- Close the valve on the propane tank.
- Unplug the heater from the electrical outlet.
4. Maintenance
Regular maintenance ensures optimal performance and longevity of your heater.
- Cleaning: Keep the heater clean and free from dust and debris. Use a soft, dry cloth for exterior cleaning. Do not use abrasive cleaners or solvents.
- Storage: When not in use, disconnect the propane tank and store the heater in a dry, safe place away from direct sunlight and extreme temperatures. Ensure the heater is cool before storing.
- Pre-Season Check: Before each heating season, inspect the hose and regulator for cracks, cuts, or damage. Replace if necessary. Ensure all connections are secure.
5. Troubleshooting
If you encounter issues with your heater, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not ignite | No propane flow, faulty ignition, no electrical power | Check propane tank valve, ensure tank has fuel, verify electrical connection, check ignition button. |
| Flame goes out during operation | Low propane, insufficient ventilation, safety flame-out system activated | Replace propane tank, ensure adequate ventilation, restart heater after checking connections. |
| Heater shuts off unexpectedly | Overheat protection activated, low oxygen sensor activated | Allow heater to cool, ensure proper ventilation, check for obstructions. |
| Smell of gas | Gas leak | Immediately shut off propane tank, unplug heater, evacuate area, and contact qualified service personnel. Do not operate. |
If problems persist after attempting these solutions, contact BILT HARD customer service.
6. Specifications
| Feature | Specification |
|---|---|
| Brand | BILT HARD |
| Model Number | FAH-G125-BG |
| Heat Output | 75,000 - 125,000 British Thermal Units (BTU) |
| Fuel Type | Propane |
| Voltage | 120 Volts (AC) |
| Product Dimensions | 30.58"D x 25.6"W x 53.5"H |
| Item Weight | 16.76 pounds |
| Special Feature | Portable, Adjustable Heat Angle |
| Safety Certifications | CSA Listed |
7. Warranty and Support
The BILT HARD propane forced air heater is guaranteed for 1 year from the date of purchase. This warranty covers manufacturing defects and quality problems.
For warranty claims, technical support, or any questions regarding your heater, please contact BILT HARD customer service directly. We are committed to providing quality customer service and offer free exchange for any quality problems within the warranty period.
Please have your model number (FAH-G125-BG) and proof of purchase available when contacting support.
