1. Introduction
This manual provides essential information for the proper use and maintenance of your ICOM OPC-2344-1 EX OPC-1122U USB Programming Cable. This cable is designed to connect compatible ICOM radio devices to a computer, allowing for programming and configuration via dedicated software. Please read this manual thoroughly before use to ensure optimal performance and to prevent damage.
2. Product Overview
The ICOM OPC-2344-1 EX OPC-1122U is a specialized USB programming cable. It features a standard USB-A connector for connection to your computer and a proprietary connector for interfacing with compatible ICOM radio devices. The cable facilitates the transfer of programming data, enabling users to update firmware, adjust settings, and manage channels on their ICOM radios.
Figure 2.1: The ICOM OPC-2344-1 EX OPC-1122U USB Programming Cable. The image displays the black USB cable with a standard USB-A connector on one end and a specialized programming interface on the other, designed for ICOM radio devices.
3. Setup
3.1 Driver Installation
Before connecting the programming cable, it is crucial to install the necessary drivers on your computer. These drivers ensure proper communication between the cable, your computer, and the ICOM radio.
- Visit the official ICOM website: https://www.icomjapan.com/
- Navigate to the support or downloads section.
- Locate and download the drivers specifically for the OPC-2344-1 EX OPC-1122U USB Programming Cable.
- Follow the on-screen instructions to complete the driver installation. It is recommended to restart your computer after installation if prompted.
3.2 Connecting the Cable
Once the drivers are installed, you can connect the programming cable.
- Connect the USB-A end of the OPC-2344-1 EX OPC-1122U cable to an available USB port on your computer.
- Connect the specialized connector end of the cable to the programming port on your compatible ICOM radio device. Ensure a secure connection.
4. Operating
The OPC-2344-1 EX OPC-1122U cable acts as an interface. Programming your ICOM radio requires specific programming software provided by ICOM or third-party developers, which is not included with this cable.
4.1 Compatible ICOM Devices
This cable is compatible with a range of ICOM devices, including but not limited to:
- IC-F110SN, IC-F210S N/W
- IC-F110N, IC-F210 N/W
- IC-F510N, IC-F610 MPT N/W
- IC-F1710, IC-F2710
- IC-F1810, IC-F2810
- IC-F5062 #03, IC-F6062 #03
- IC-FR6100, IC-FR5100, FR-5300, FR-6300
- IC-F5022 BIIS, IC-F6022 BIIS
- IC-F5062 #13, IC-F6062 #13
- IC-F5062D #33, IC-F6062D #33
- IC-F5062D #83, IC-F6062D #83
- IC-F5122D#01, IC-F6122D#01
4.2 Programming Procedure (General)
The exact programming steps depend on the specific ICOM radio model and the programming software used. Generally, the process involves:
- Ensure the ICOM radio is powered on and in programming mode (if applicable).
- Launch the ICOM programming software on your computer.
- Select the correct COM port associated with the USB programming cable within the software settings.
- Establish communication between the software and the radio.
- Load or create your desired radio configuration within the software.
- Write (upload) the configuration from the software to the radio.
- Verify the programming was successful and disconnect the cable.
5. Maintenance
Proper care will extend the life of your programming cable.
- Storage: Store the cable in a cool, dry place, away from direct sunlight and extreme temperatures.
- Handling: Avoid sharp bends, kinks, or excessive pulling on the cable. Do not yank the cable from ports; always grasp the connector.
- Cleaning: If necessary, gently wipe the cable and connectors with a soft, dry cloth. Do not use liquid cleaners or solvents.
- Inspection: Periodically inspect the cable for any signs of damage, such as frayed wires, bent pins, or cracked insulation. Do not use a damaged cable.
6. Troubleshooting
If you encounter issues with your programming cable, refer to the following common troubleshooting steps:
6.1 Cable Not Recognized by Computer
- Driver Check: Ensure that the correct drivers for the OPC-2344-1 EX OPC-1122U cable are properly installed. You may need to reinstall them or update them from the ICOM website.
- USB Port: Try connecting the cable to a different USB port on your computer. Avoid using unpowered USB hubs.
- Cable Integrity: Inspect the cable for any visible damage. A damaged cable may not function correctly.
- Restart: Restart your computer and try connecting the cable again.
6.2 Communication Error with Radio
- Radio Compatibility: Verify that your ICOM radio model is listed as compatible with the OPC-2344-1 EX OPC-1122U cable.
- Secure Connection: Ensure the cable is firmly connected to both the computer and the radio.
- Radio Mode: Confirm that the radio is powered on and in the correct programming mode, if required by the radio model.
- Software Settings: In your programming software, ensure the correct COM port is selected and that the software version is compatible with your radio and cable.
- Other Software: Close any other applications that might be using the COM port.
7. Specifications
| Feature | Detail |
|---|---|
| Product Name | ICOM OPC-2344-1 EX OPC-1122U USB Programming Cable |
| Brand | ICOM |
| Connector Type | USB |
| Number of Items | 1 |
| Manufacturer | Icom |
| ASIN | B0BCH1G81N |
| First Available Date | August 30, 2022 |
8. Support & Resources
For further assistance, driver downloads, or detailed information regarding your ICOM radio and programming software, please visit the official ICOM website:
You may also consult the user manual for your specific ICOM radio model for programming instructions relevant to that device.
