SW-Motech STP.05.590.10900/B

Download PDF
Contents

SW-MOTECH Crash Pad Kit Installation Manual for SUZUKI GSX-S 1000 (2021-)

Model: STP.05.590.10900/B

Introduction

This manual provides detailed instructions for the proper installation, operation, and maintenance of the SW-MOTECH Crash Pad Kit, designed specifically for the SUZUKI GSX-S 1000 motorcycle models from 2021 onwards. Please read these instructions thoroughly before beginning installation to ensure correct fitment and optimal performance. Incorrect installation may lead to product failure or damage to your motorcycle.

For your safety, installation should be performed by a qualified technician if you are not confident in your mechanical abilities. Always wear appropriate safety gear during installation.

Package Contents

Before starting, verify that all components are present in the package. The kit should include:

  • 2x Crash Pads (Left and Right)
  • Mounting hardware (bolts, washers, spacers as required)
  • Installation instructions (this document)

If any parts are missing or damaged, please contact SW-MOTECH customer support immediately.

Required Tools

The following tools are typically required for installation:

  • Torque wrench
  • Socket set (appropriate sizes for motorcycle bolts)
  • Hex key set
  • Thread-locking compound (medium strength, e.g., Loctite 243)
  • Clean cloth

Setup and Installation

Follow these steps carefully for proper installation of the crash pad kit.

Step 1: Prepare the Motorcycle

Park the motorcycle on a stable, level surface using a center stand or paddock stand. Ensure the engine is cool before starting work. Identify the mounting points on both sides of the engine frame.

SW-MOTECH Crash Pad installed on the left side of a Suzuki GSX-S 1000 engine

Image: SW-MOTECH Crash Pad installed on the left side of a Suzuki GSX-S 1000 engine. This image shows the crash pad securely mounted to the engine casing, providing a visual reference for the correct positioning.

Step 2: Remove Existing Bolts (if applicable)

Depending on your motorcycle's configuration, you may need to remove existing engine mounting bolts or frame bolts. Refer to your motorcycle's service manual for specific torque values and procedures for these bolts. Remove one bolt at a time to maintain engine alignment.

Step 3: Install Mounting Brackets/Spacers

Attach any provided mounting brackets or spacers to the frame using the new, longer bolts supplied in the kit. Apply a small amount of medium-strength thread-locking compound to the bolt threads before tightening. Do not fully tighten yet.

Close-up view of SW-MOTECH Crash Pad mounting point on a motorcycle frame

Image: Close-up view of SW-MOTECH Crash Pad mounting point on a motorcycle frame. This image illustrates the specific attachment point and the components involved in securing the crash pad to the motorcycle's structure.

Step 4: Attach Crash Pads

Slide the crash pads onto the mounting bolts or attach them to the brackets. Ensure the SW-MOTECH logo is correctly oriented. Secure the crash pads with the provided nuts or bolts. Apply thread-locking compound as instructed.

Pair of SW-MOTECH Crash Pads, black with red logo

Image: Pair of SW-MOTECH Crash Pads, black with red logo. This image displays the two crash pads included in the kit, highlighting their design and branding before installation.

Step 5: Torque All Fasteners

Using a torque wrench, tighten all bolts to the specifications provided in the SW-MOTECH installation sheet (if separate) or your motorcycle's service manual for similar fasteners. Do not overtighten.

SW-MOTECH Crash Pad viewed from the front, showing its profile on a motorcycle

Image: SW-MOTECH Crash Pad viewed from the front, showing its profile on a motorcycle. This perspective demonstrates how the crash pad extends from the motorcycle frame, offering protection.

Step 6: Final Check

Ensure all bolts are securely tightened and the crash pads are firmly in place. Check for any obstructions or interference with other motorcycle components, especially during steering or suspension compression.

Side view of SW-MOTECH Crash Pad installed on a Suzuki GSX-S 1000

Image: Side view of SW-MOTECH Crash Pad installed on a Suzuki GSX-S 1000. This image provides a broader view of the crash pad's integration with the motorcycle's overall design.

Operating Considerations

The SW-MOTECH Crash Pad Kit is designed to offer protection to your motorcycle's frame and engine components in the event of a fall or slide. While these crash pads are robust, they are not guaranteed to prevent all damage in all situations. Always ride responsibly and within your limits.

After installation, it is recommended to perform a short test ride at low speeds to ensure no issues arise from the new components.

Maintenance

Regular inspection of your SW-MOTECH Crash Pads is crucial for continued effectiveness.

  • Visual Inspection: Periodically check the crash pads for any signs of damage, cracks, or wear.
  • Fastener Check: Ensure all mounting bolts remain tight. Re-torque to specifications if necessary, especially after the first 50-100 miles of riding post-installation.
  • Cleaning: Clean the crash pads with a mild soap and water solution. Avoid harsh chemicals that may damage the material.
  • Post-Incident Inspection: If your motorcycle experiences a fall or slide, thoroughly inspect the crash pads and their mounting points for any damage. Replace damaged components immediately.

Troubleshooting

ProblemPossible CauseSolution
Crash pad feels looseMounting bolts are not sufficiently tightened.Re-torque all mounting bolts to the specified values. Ensure thread-locking compound was applied.
Vibration from crash padsLoose fasteners or improper installation.Check all mounting points for tightness. Ensure no components are interfering with the frame or engine.
Crash pad appears damaged after a minor fallImpact exceeded the material's tolerance.Replace the damaged crash pad and any associated mounting hardware immediately.

Specifications

  • Model: STP.05.590.10900/B
  • Compatibility: SUZUKI GSX-S 1000 (Model Year 2021 and newer)
  • Material: High-strength synthetic material (crash pads), steel/aluminum (mounting hardware)
  • Color: Black
  • Item Weight: Approximately 4.4 pounds (total package)
  • Package Dimensions: Approximately 7.87 x 7.87 x 3.94 inches

Warranty and Support

SW-MOTECH products are manufactured to high-quality standards. For specific warranty information, please refer to the official SW-MOTECH website or contact your authorized dealer. Keep your proof of purchase for warranty claims.

For technical support, missing parts, or further assistance, please visit the SW-MOTECH official website or contact their customer service department.

© 2023 SW-MOTECH. All rights reserved.

This manual is subject to change without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.