Deante BCH_064M 3-Way Filtered Water Tap User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Deante BCH_064M 3-Way Filtered Water Tap. This tap is designed to provide hot, cold, and filtered water from a single unit, featuring a U-type swan neck spout and a chrome finish. Please read these instructions carefully before installation and use to ensure proper function and longevity of the product.

Figure 1: Deante BCH_064M 3-Way Filtered Water Tap. This image shows the complete tap unit with its U-type swan neck spout and two control levers, all in a polished chrome finish.

2. Safety Information

• Always turn off the main water supply before beginning any installation or maintenance work.
• Ensure all connections are properly sealed to prevent leaks.
• If you are unsure about any part of the installation process, consult a qualified plumber.
• Do not use abrasive cleaners or harsh chemicals on the chrome finish, as this may damage the surface.
• Keep small parts out of reach of children.

3. Package Contents

Verify that all components are present before starting installation:

• 1 x Deante BCH_064M Kitchen Sink Tap with connection for water filter (Chrome)
• Mounting Set (washers, nuts, fixing screws)
• Connection Hoses (450 mm length)
• User Manual (this document)

4. Specifications

Figure 2: Technical drawing illustrating the dimensions and connection points of the Deante BCH_064M tap. Key measurements include total height (344mm), spout reach (180mm), and various connection thread sizes.

5. Installation

Before starting, ensure the main water supply is turned off. Refer to Figure 2 for a visual guide on dimensions and connection points.

1. Prepare the Mounting Surface: Ensure the sink or countertop has a single hole suitable for deck mounting. The tap requires a hole with a diameter of approximately 33mm (refer to Figure 2 for exact dimensions).
2. Insert the Tap: Place the tap body into the mounting hole. Ensure the base gasket is correctly positioned between the tap and the mounting surface to prevent leaks.
3. Secure the Tap: From underneath the sink/countertop, slide the rubber washer, metal washer, and then the fixing nut onto the threaded rod extending from the tap base. Tighten the fixing nut securely using the provided tool or an appropriate wrench. Do not overtighten.
4. Connect Water Hoses:
   • Connect the hot and cold water supply hoses (3/8'' installation thread, M10 connection thread) to your existing hot and cold water lines. Ensure the correct hose is connected to the corresponding supply.
   • Connect the filtered water hose (1/4'' connection, as indicated in Figure 2) to your water filter system's output.
5. Check for Leaks: Once all connections are made, slowly turn on the main water supply. Inspect all connections for any signs of leaks. If leaks are detected, turn off the water supply and re-tighten the connections.
6. Flush the System: Allow water to run through the tap for a few minutes to flush out any debris from the new installation.

Figure 3: The Deante 3-Way Filtered Water Tap installed in a kitchen sink, demonstrating its integration into a typical kitchen environment. This image shows the tap positioned next to a stainless steel sink with a drainer.

6. Operation

The Deante BCH_064M tap features two distinct levers for controlling water flow:

• Main Mixer Lever: This lever controls the hot and cold water supply. Moving it left or right adjusts the temperature, while moving it up or down controls the flow rate.
• Filtered Water Lever: A separate, smaller lever is dedicated to dispensing filtered water. Operate this lever independently to access purified water.

The swan neck spout is designed to swivel 360°, providing flexibility and ease of use for various sink tasks.

Figure 4: The Deante 3-Way Filtered Water Tap integrated into a larger kitchen setting, highlighting its contemporary style and functional design. The tap is centrally located on a kitchen island with a sink.

7. Maintenance

Regular maintenance will help preserve the appearance and functionality of your tap.

• Cleaning the Finish: Clean the chrome finish regularly with a soft cloth and mild soap and water. Rinse thoroughly and dry immediately to prevent water spots. Avoid abrasive cleaners, scouring pads, or chemical solvents, as these can damage the chrome.
• Aerator Cleaning: Periodically unscrew the aerator (M22 size) from the end of the spout. Clean any mineral deposits or debris from the mesh screen. Reattach securely.
• Ceramic Cartridge: The tap uses a 35mm ceramic head (cartridge). If you experience persistent drips or difficulty controlling water flow, the ceramic cartridge may need replacement. This is typically a task for a qualified plumber.
• Filter Replacement: If using a water filter system, follow the manufacturer's instructions for regular filter replacement to ensure continued purified water quality.

8. Troubleshooting

9. Warranty and Support

For warranty information, please refer to the terms and conditions provided at the point of purchase or contact your retailer. For technical support or replacement parts, please contact DEANTE customer service or your authorized dealer. Keep your proof of purchase for any warranty claims.

Manufacturer: Deante

Model Number: BCH_064M