CREATE WINDCALM Ceiling Fan with Light

Introduction

Thank you for choosing the CREATE WINDCALM Ceiling Fan with Light. This manual provides essential instructions for safe installation, operation, and maintenance of your new ceiling fan. Please read this manual thoroughly before installation and keep it for future reference.

Safety Information

WARNING: To avoid electric shock, ensure power is disconnected at the main circuit breaker before installation or maintenance.

• Ensure the installation surface can support the fan's weight.
• All wiring must be in accordance with national and local electrical codes.
• Do not connect the fan to a dimmer switch.
• Maintain a minimum clearance of 2.3 meters (7.5 feet) from the floor to the fan blades.
• Do not insert objects into the path of the fan blades.

Package Contents

Verify that all components are present before beginning installation:

• Mounting Bracket
• Driver
• Remote Control
• LED Plate (for models with light)
• Glass Lampshade (for models with light)
• Decorative Element
• Motor Housing
• Fan Blades (3x)
• Terminal Block
• Balancing Kit
• Decorative Cover
• Various Screws and Washers
• Remote Control (included)

Installation Guide

This section provides a step-by-step guide for installing your CREATE WINDCALM ceiling fan. For a visual demonstration, please refer to the official installation video below.

Step 1: Mounting Bracket Installation

The mounting bracket must be securely attached to the ceiling. The method varies based on your ceiling type:

For Wooden Ceilings:

1. Position the mounting bracket on the ceiling where you intend to install the fan.
2. Mark the drilling points through the holes in the bracket.
3. Drill pilot holes (6mm diameter) at the marked points.
4. Secure the mounting bracket using the provided wood screws. Ensure the wires pass through the center opening.

For Concrete Ceilings:

1. Position the mounting bracket on the ceiling.
2. Mark the drilling points.
3. Drill holes (8mm diameter) at the marked points.
4. Insert the expansion bolts into the drilled holes.
5. Secure the mounting bracket with the expansion bolts. Ensure the wires pass through the center opening.

For False Ceilings:

1. Position the mounting bracket on the ceiling.
2. Mark the drilling points.
3. Drill holes at the marked points.
4. Insert the toggle bolts (not included, purchase separately if needed) through the holes in the bracket and into the ceiling.
5. Tighten the toggle bolts to secure the mounting bracket. Ensure the wires pass through the center opening.

Step 2: Driver and Electrical Connection

Connect the fan's electrical components to your home's wiring. Ensure all connections are secure and insulated.

1. Connect the neutral (N) wire from your home to the neutral (N) wire of the driver.
2. Connect the live (L) wire from your home to the live (L) wire of the driver.
3. If your electrical installation lacks an earth connection, connect the earth cable from the support to the earth cables of the driver and motor.
4. Connect the motor wires to the driver wires according to the color coding (e.g., blue to blue, brown to brown).
5. Ensure all connections are tight and no wires are pinched.

Step 3: Anchoring the Motor to the Ceiling

Carefully lift the fan motor and attach it to the installed mounting bracket.

1. Align the motor housing with the mounting bracket.
2. Secure the motor housing to the bracket using the designated screws. Ensure all wires are tucked neatly inside the housing and not pinched.

Step 4: Assembling Fan Blades

Attach the wooden fan blades to the motor. Do not overtighten the screws to allow for proper alignment.

1. Carefully align each fan blade with the corresponding mounting points on the motor.
2. Insert the screws and tighten them securely, but avoid overtightening to prevent damage to the blades.

Step 5: Placing the Decorative Element

Install the decorative element that covers the blade attachment points.

1. Position the decorative element over the center of the fan, covering the blade screws.
2. Secure it with the small screws provided.

Step 6: LED Kit Connection (Optional) / Cover Mounting

If your fan includes an LED light kit, follow these steps. If not, proceed to mount the bottom cover.

For Models with LED Light Kit:

1. Connect the LED plate wires to the corresponding wires from the fan motor.
2. Secure the LED plate to the motor using the provided screws.

For Models without LED Light Kit:

1. Attach the decorative bottom cover to the motor housing, ensuring it is securely fastened.

Step 7: Lampshade Placement (for models with light)

Carefully attach the glass lampshade to the fan.

1. Align the lampshade with the fan's light fixture.
2. Twist or push the lampshade into place until it is securely seated.

Operating Instructions

Your CREATE WINDCALM fan is controlled via the included remote control.

• Power On/Off: Press the power button to turn the fan on or off.
• Speed Control: Select from 6 available speeds to adjust airflow.
• Timer Function: Program the fan to turn off automatically after 1, 2, or 4 hours.
• Summer/Winter Mode:
  • Summer Mode: Blades rotate counter-clockwise, pushing cool air downwards to create a refreshing breeze.
  • Winter Mode: Blades rotate clockwise, drawing cool air upwards and distributing warm air accumulated near the ceiling evenly throughout the room.
• LED Lighting (if applicable): Choose between three color temperatures (warm, neutral, cool) for the 15W LED light. Light intensity is not adjustable.

Remote control for easy operation of fan speeds, timer, and light settings.

Visual representation of key features: 1-4 hour timer, ultra-quiet operation, and 6 speed settings.

Illustration of the three adjustable light color temperatures: warm, neutral, and cool.

Summer mode operation: Fan blades rotate counter-clockwise, pushing air downwards for a cooling effect.

Winter mode operation: Fan blades rotate clockwise, drawing cool air upwards to redistribute warm air.

Maintenance

• Always disconnect power before cleaning or performing any maintenance.
• Clean the fan blades and motor housing with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Regularly check all connections and screws to ensure they remain tight.

Troubleshooting

Specifications

Energy efficiency label for the fan. For more details, visit the EPREL database.

Energy efficiency label for the integrated LED light kit.

Warranty and Support

Your CREATE WINDCALM Ceiling Fan is covered by a manufacturer's warranty. For warranty claims, technical support, or any questions regarding your product, please contact CREATE customer service through their official channels or the retailer from whom you purchased the product.