1. Product Overview
The Nextion Intelligent 7.0 inch HMI Display (model NX8048P070-011C) is a 5V capacitive touch screen TFT LCD with 800x480 resolution. It is designed for Human Machine Interface (HMI) applications and is compatible with various microcontrollers, including Arduino and ESP32.
This Intelligent series display offers enhanced hardware capabilities compared to Nextion Basic and Enhanced models, featuring a more powerful MCU, increased Flash storage, and greater SRAM. These improvements enable advanced functionalities such as audio, video, and animation playback, significantly enriching the HMI interaction experience.
The display supports advanced software features including transparent components, dynamic page loading effects, and component movement and dragging at runtime. It integrates seamlessly with the user-friendly Nextion HMI software, which utilizes ASCII text-based instructions over serial communication for intuitive GUI design and interaction.


2. Specifications
| Feature | Value |
|---|---|
| Model Number | NX8048P070-011C |
| Screen Size | 7 Inches |
| Resolution | 800 x 480 |
| Touch Panel Type | Capacitive Touch Screen |
| Voltage | 5 Volts |
| Image Brightness | 300 candela/m² |
| Aspect Ratio | 16:9 |
| Screen Surface Description | Glossy |
| Package Dimensions | 7.95 x 5.24 x 1.5 inches |
| Item Weight | 12.3 ounces |


3. Setup and Power Supply
The Nextion Intelligent 7.0 display is a 5V device. It is crucial to provide adequate power for proper operation. Many development boards operate at 3.3V, which is insufficient to power this display.
3.1 Recommended Power Supply
To ensure the Nextion 7.0 intelligent display functions as expected, it is highly recommended to supply power via a dedicated power adapter. Powering the display directly from a USB to TTL converter or certain development boards may not provide stable or sufficient current, even if the PC's USB port is rated at 5V.
3.2 Power Connection via Micro USB (for testing)
For initial testing or if a dedicated power adapter is unavailable, you can use a micro USB cable with a 5V 2A power supply adapter. A small green board and 4-pin wire are typically included to facilitate this connection.
- Insert the XH2.54 4P wire into the display's connector.
- Connect the VCC wire to the '+' terminal and the GND wire to the '-' terminal on the small green board.
- Connect the micro USB cable to the green board.
- Connect the micro USB cable to a 5V 2A power supply adapter.
- Power on the display.
Caution:
Working under insufficient power supply conditions can damage the Nextion display. A blurred screen or flashing indicates power shortages. Power off immediately if this occurs. Always use a high-quality USB cable and ensure your power source provides stable 5V 2A.

Video 3.1: This video demonstrates the process of powering the Nextion display via a Micro USB 5V connection.
4. Operating Instructions
The Nextion Intelligent display is programmed using the Nextion Editor software. This software allows for the creation of graphical user interfaces (GUIs) and interaction logic.
4.1 Nextion Editor Software
The Nextion Editor is an easy-to-use HMI software that supports ASCII text-based instructions over serial communication. It features drag-and-drop components for GUI design and interaction, and a user event code pane for GUI interaction and peripheral MCU communication.



4.2 Uploading Project Files (TFT)
There are two primary methods for uploading your compiled project (.TFT file) to the Nextion display:
4.2.1 Via SD Card
Uploading the TFT file via an SD card is generally faster than using a USB to TTL converter.
- Prepare an SD card: It must be formatted as FAT32 and have a capacity of no more than 32GB.
- Copy the compiled .TFT file from your PC to the SD card. Ensure there is only one .TFT file in the root directory of the card (no folders).
- Insert the SD card into the Nextion display's card slot.
- Power on the Nextion display. The file will be uploaded automatically, and the display will show "Update Succeeded!" upon completion.
- Power off the Nextion display, remove the SD card, and then power it back on. Your project will now be displayed.
Video 4.1: This video demonstrates how to program the Nextion display using an SD card.
4.2.2 Via USB to TTL Converter
This method requires a USB to TTL serial port module. Only CP2102 or FT232 based modules are recommended. CH340 or PL2302 modules may cause upload failures.
- Connect the USB to TTL module to the Nextion display: 5V to 5V, GND to GND, TX to RX, and RX to TX.
- Open the Nextion Editor software on your PC.
- Click the "Upload" button in the Nextion Editor.
- Select the correct COM Port for your USB to TTL module (check Device Manager if unsure) and choose a suitable Baud Rate. A higher baud rate can speed up the upload process.
- Click "Go" to start the upload. The process will take a few minutes.
- Once completed, the software will indicate "Download finished!" and the total time taken.
Video 4.2: This video demonstrates how to program the Nextion display via a USB to TTL converter.
5. Maintenance
The Nextion Intelligent HMI Display is designed for durability and generally requires minimal maintenance. Keep the screen clean using a soft, dry, anti-static cloth. Avoid using harsh chemicals or abrasive materials that could damage the capacitive touch surface.
Ensure proper ventilation around the display if it is integrated into an enclosure to prevent overheating, which can affect performance and longevity.
6. Troubleshooting
6.1 Common Issues and Solutions
- Q: Can Nextion display be used with other MCUs?
A: Nextion displays are compatible with many microcontrollers. Libraries are officially provided for Arduino and Linux. For other MCUs, you will need to develop your own libraries, ensuring all instructions strictly follow the Nextion Instruction Set. - Q: How to upload the designed project?
A: Projects can be uploaded via a USB to TTL module or an SD card. - Q: Can Nextion read files from an SD card?
A: No, the SD card is exclusively used for uploading the .TFT project file to the display's internal memory. It cannot be used for general file storage or reading by the display during operation. - Q: My project is successfully made in Nextion Editor. How do I get the .TFT file?
A: In Nextion Editor, select "File" then "TFT file output." Click "Output" and save the generated .TFT file to your desired location. - Q: Can I output the .TFT file directly from the Nextion screen?
A: No, the .TFT file is generated by the Nextion Editor software on your computer. - Q: I want to update my project, but the .TFT file cannot be revised. Why?
A: The .TFT file is a compiled binary. You should edit the original .HMI project file within the Nextion Editor software, then recompile and output a new .TFT file. - Q: Nextion Editor shows "Can not open this file (Your HMI file is made by low version Editor)"?
A: This error indicates that your project file was created with an older version of the Nextion Editor. You need to download and use the newest version of the software to open and work with the file. - Q: The Nextion display shows "Model does not match" or "File Info ERROR!" How to solve it?
A: This error occurs if the .TFT file was compiled for a different Nextion model. You need to re-select the correct model number for your display within the Nextion Editor and then recompile the project.
7. Warranty Information
Specific warranty details for the DIYmalls Nextion Intelligent 7-inch HMI Display (NX8048P070-011C) are not provided in the available product information. Please refer to the retailer or manufacturer's official website for current warranty terms and conditions.
8. Support and Contact
For further assistance, technical support, or additional resources regarding your DIYmalls Nextion Intelligent 7-inch HMI Display, please refer to the following:
- Manufacturer: DIYmalls
- Nextion Editor Software: https://nextion.tech/nextion-editor/
- Editor Guide, Instructions, Datasheet: https://nextion.tech/
- Nextion Compatible with Arduino: https://randomnerdtutorials.com/nextion-display-with-arduino-getting-started/
- General Video Link (YouTube search for Nextion HMI): https://www.youtube.com/results?search_query=Nextion+HMI
You may also find answers to common questions in the Troubleshooting section of this manual.