WOBANE Under Cabinet Lighting (Model CS4) Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your WOBANE 24-inch LED Under Cabinet Light Bar. This product features hand wave activation, touchless dimming, and tunable white color temperatures from 2700K to 6500K, designed to enhance lighting in various indoor spaces such as kitchens, shelves, and desks.

Package Contents

• 1 x 24-inch LED Light Bar
• 1 x Power Adapter (8.2 ft / 2.5m cord)
• 3 x Cable Holders
• 2 x Mounting Screws

Image: The WOBANE 24-inch LED light bar, power adapter, cable holders, and mounting screws are shown as included components.

Setup and Installation

1. Prepare the Installation Area: Choose a clean, dry, and flat surface for mounting. Ensure the area is free from dust and moisture.
2. Determine Mounting Position: Identify the desired location for the light bar. The light bar has two power ports, allowing flexibility in cable routing.
3. Install Mounting Screws:
   • Remove the end cap from the light bar to access the screw holes.
   • Mark the positions for the two mounting screws on your chosen surface.
   • Drill pilot holes if necessary, then secure the light bar using the provided screws.
   • Replace the end cap after securing the light bar.
4. Connect Power: Plug the power adapter into one of the light bar's power ports. Connect the adapter to a standard electrical outlet. The extra-long 8.2 ft power cord provides ample reach.
5. Organize Cables: Use the included cable holders to neatly route and secure the power cord, preventing tangles and ensuring a clean installation.

Image: A visual guide showing the four steps for installation: 1. Removing the end cap, 2. Screwing the light bar into place, 3. Plugging in the power adapter, and 4. The light bar in operation.

Operating Instructions

Hand Wave Activation (On/Off)

The WOBANE light bar features a touchless infrared (IR) sensor for convenient operation. To turn the light ON or OFF, simply wave your hand within 3 inches (7.6 cm) of the IR sensor. This allows for easy control, even with wet hands.

Image: A hand is shown waving over the light bar's IR sensor, illustrating the touchless activation feature. The sensor range is indicated as 3 inches.

Touchless Dimming Control

To adjust the brightness level, hold your hand steadily under the IR sensor. The light will gradually dim or brighten. Remove your hand when the desired brightness is achieved. The light will remember your last brightness setting when turned off and on again.

Color Temperature Adjustment

The light bar offers five color temperature options: 2700K (Warm White), 3000K (Soft White), 4000K (Neutral White), 5000K (Cool White), and 6500K (Daylight White). To cycle through these options, locate the small switch on the side of the light bar (often near the power input) and toggle it to select your preferred color temperature.

Image: The light bar illuminates a desk area, demonstrating different color temperatures from warm (3000K) to cool (6000K), with a detailed inset showing the color temperature selection switch.

Maintenance

The WOBANE LED light bar is designed for long-lasting performance with minimal maintenance. Follow these guidelines to ensure optimal operation:

• Cleaning: Disconnect the power before cleaning. Use a soft, dry, or slightly damp cloth to wipe the surface of the light bar. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or electronic components.
• Sensor Care: Keep the IR sensor area clean and unobstructed to ensure proper hand wave detection.
• General Inspection: Periodically check the power cord and connections for any signs of damage. If any damage is observed, discontinue use and contact customer support.

Troubleshooting

Specifications

Safety Information

Please read and understand all safety instructions before installing or using this product. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• This product is intended for indoor use only. Do not expose to water or moisture.
• Ensure the power supply voltage matches the product's requirements (120V).
• Do not attempt to disassemble or modify the light bar or power adapter. There are no user-serviceable parts inside.
• Keep the power cord away from heat sources, sharp edges, and moving parts.
• Always unplug the light bar from the power outlet before cleaning or performing any maintenance.
• If the power cord or adapter is damaged, do not use the product. Contact customer support for assistance.
• Keep out of reach of children.

Warranty and Support

WOBANE products are designed for quality and reliability. For any questions, technical support, or warranty claims, please contact WOBANE customer service. Refer to your purchase documentation for specific warranty terms and contact information.

You can typically find support contact details on the seller's page or through the platform where the product was purchased.