Introduction
Thank you for choosing the Hibbent Replacement Kitchen Faucet Head. This product is designed to enhance your kitchen experience with its versatile spray modes and easy installation. This manual provides detailed instructions to ensure proper setup, operation, and maintenance of your new faucet head.
Safety Information
- Always turn off the water supply before attempting any installation or maintenance.
- Use appropriate tools and wear protective eyewear during installation.
- Ensure all connections are secure to prevent leaks.
- Do not use abrasive cleaners or harsh chemicals on the faucet head, as this may damage the finish.
Package Contents
- 1 x Hibbent Replacement Kitchen Faucet Head (Brushed Nickel)
- 9 x Connection Adapters (various sizes)
- User Manual (this document)
Installation Guide
The Hibbent faucet head is designed for easy replacement. It is compatible with most pull-down kitchen sink taps. Please ensure your existing faucet has a pull-down hose for direct installation.
- Turn off Water Supply: Locate the water shut-off valves under your kitchen sink and turn them off.
- Remove Old Faucet Head: Unscrew your existing faucet head from the pull-down hose. You may need a wrench if it's tightly secured.
- Select Correct Adapter: Identify the correct adapter from the 9 provided that matches the thread of your pull-down hose. The adapters include sizes like 5/8-16 UN, 5/8-18 UNF, G 1/2" (with 3 heights), and male threads of 17.1mm, 16.4mm, 15.5mm, and 14mm.
- Attach Adapter (if needed): If your hose requires an adapter, screw it onto the end of the pull-down hose. Ensure a tight, secure fit.
- Attach New Faucet Head: Screw the Hibbent Replacement Kitchen Faucet Head onto the selected adapter or directly onto the pull-down hose if no adapter is needed. Hand-tighten first, then use a wrench for a final snug fit, being careful not to overtighten.
- Check for Leaks: Slowly turn the water supply back on and check for any leaks around the connection points. If leaks occur, tighten the connection further or re-check the adapter and seals.
Operating Instructions
Your Hibbent faucet head offers three distinct spray modes for various kitchen tasks.
- Mode Switching: Press the button located on the side of the faucet head to cycle through the three modes: Stream, Spray, and Aquablade.
- Stream Mode: Provides a steady, aerated flow, ideal for filling pots and general washing.
- Spray Mode: A wider, softer spray, suitable for rinsing dishes and produce.
- Aquablade Mode: A powerful, concentrated blade of water designed for quickly washing away stubborn food debris.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your faucet head.
- Cleaning the Aerator: The faucet head is equipped with a multi-mesh aerator that can be removed and cleaned. Periodically unscrew the aerator (usually by hand or with a coin) and rinse it under running water to remove any mineral deposits or debris. This helps maintain a perfect, splash-free flow.
- Exterior Cleaning: Clean the exterior of the faucet head with a soft cloth and mild soap and water. Avoid using abrasive cleaners, scouring pads, or harsh chemicals, as these can damage the brushed nickel finish.
- Check for Leaks: Periodically inspect the connection points for any signs of leaks. Tighten connections as needed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks from connection point | Loose connection; incorrect adapter; damaged washer/seal. | Ensure the faucet head is tightly screwed onto the hose/adapter. Verify the correct adapter is used and that all washers/seals are properly seated and undamaged. Re-tighten carefully. |
| Low water pressure or irregular flow | Clogged aerator; debris in the hose. | Remove and clean the aerator as described in the Maintenance section. Check the pull-down hose for any obstructions. |
| Cannot switch spray modes | Button stuck or internal mechanism issue. | Ensure the button is not obstructed. If the issue persists, contact customer support. |
| Faucet head does not fit existing hose | Incorrect thread size; not a pull-down faucet. | Verify your faucet is a pull-down type. Try all included adapters to find the correct fit. If none fit, your faucet may have a non-standard thread not supported by the included adapters. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Hibbent |
| Model Number | CAPD75032spray3 |
| Color | Brushed Nickel |
| Material | Engineering Grade Plastic (PC/ABS) |
| Finish Type | Brushed |
| Product Dimensions (L x W x H) | 5.5 x 3 x 10 cm |
| Item Weight | 158.76 grams |
| Installation Method | Deck Mounted |
| Special Features | 3 spray modes, 9 adapters for various connections, Removable and Washable Aerator, Automatic reset to stream mode |
Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact Hibbent customer service directly. Keep your purchase receipt for any warranty claims.
For further assistance, please visit our official website or contact our support team via the contact information provided with your purchase.
