1. Introduction
Thank you for choosing the LUTEC Polo LED Outdoor Wall Light. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixture. Please read these instructions carefully before installation and retain them for future reference.
2. Safety Information
- Electrical Safety: Installation must be performed by a qualified electrician in accordance with all local and national wiring regulations. Ensure the power supply is disconnected at the main circuit breaker before commencing any installation or maintenance work.
- Voltage: This fixture operates on 230 Volts (AC). Verify your power supply matches this requirement.
- Protection Class: This product is Class I, meaning it must be earthed.
- IP Rating: The fixture has an IP54 rating, indicating protection against dust ingress and splashing water from any direction. It is suitable for outdoor use but should not be submerged.
- Handling: Do not handle the fixture with wet hands. Avoid touching the LED light source directly when illuminated.
- Damage: Do not use the fixture if any part is damaged. Contact customer support for replacement parts.
3. Package Contents
Please check that all components are present before installation:
- 1x LUTEC Polo LED Outdoor Wall Light (Model 5205702118)
- Mounting accessories (screws, wall plugs)
- Instruction Manual
4. Setup and Installation
Follow these steps for proper installation. It is recommended to have two people for installation.
- Prepare the Installation Area: Choose a suitable location on an exterior wall. The recommended mounting height for optimal motion sensor performance is 2.5 meters. Ensure the power supply is turned off at the main circuit breaker.
- Mark Drilling Points: Hold the mounting bracket against the wall at the desired installation height. Use a pencil to mark the drilling points.
- Drill Holes: Drill holes at the marked points using an appropriate drill bit for your wall material. Insert the provided wall plugs.
- Secure Mounting Bracket: Attach the mounting bracket to the wall using the provided screws. Ensure it is firmly secured.
- Electrical Connection: Connect the electrical wires from your mains supply to the terminal block on the fixture. Ensure correct polarity (Live, Neutral, Earth) and secure all connections.
- Mount the Fixture: Carefully attach the light fixture to the mounting bracket, ensuring all wires are tucked away safely and not pinched. Secure the fixture with any retaining screws.
- Restore Power: Once the fixture is securely mounted and all connections are checked, restore power at the main circuit breaker.
Figure 1: Front view of the LUTEC Polo LED Outdoor Wall Light, showcasing its modern anthracite finish and circular design.
Figure 2: The LUTEC Polo LED Outdoor Wall Light installed on an exterior brick wall, demonstrating its appearance when illuminated.
Figure 3: A wider shot of the LUTEC Polo LED Outdoor Wall Light installed on an exterior wall, providing ambient lighting to the area.
5. Operating Instructions
The LUTEC Polo LED Outdoor Wall Light is designed for automatic operation thanks to its integrated motion sensor. Once installed and powered, the light will activate based on the motion sensor settings.
6. Motion Sensor Settings
The integrated motion sensor allows for customization of detection parameters. Adjustments are typically made via small dials or switches located on the sensor unit itself (refer to Figure 4 for sensor location). The specific adjustment method may vary; consult the detailed diagram or markings on the sensor.
- Detection Angle: The sensor has a 180-degree detection angle.
- Detection Range: Adjustable from 0 to 10 meters (when mounted at 2.5 meters height).
- Timer (Illumination Duration): Adjustable from 10 seconds up to 10 minutes. This controls how long the light stays on after motion is detected.
- Light Sensitivity (LUX): Adjustable to 10 lux. This setting determines the ambient light level at which the sensor becomes active. For example, at 10 lux, the light will only activate when it is relatively dark.
Figure 4: Close-up view of the integrated motion sensor located at the bottom of the LUTEC Polo LED Outdoor Wall Light. Adjustment dials are typically found here.
7. Maintenance
- Cleaning: To clean the fixture, ensure the power is off. Use a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or electrical components.
- LEDs: The integrated LED light source is not user-replaceable. If the LED fails, the entire fixture may need to be replaced.
- Inspection: Periodically inspect the fixture for any signs of damage, loose connections, or wear.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. Sensor sensitivity too low (too bright). Faulty wiring. | Check circuit breaker. Adjust LUX setting on sensor. Consult a qualified electrician to check wiring. |
| Light stays on continuously. | Continuous motion detected. Timer setting too long. Sensor malfunction. | Check for obstructions or constant movement in detection area. Adjust timer setting to a shorter duration. Contact customer support. |
| Light flashes or flickers. | Unstable power supply. Loose wiring connection. Faulty LED driver. | Consult an electrician to check power supply. Ensure all wiring connections are secure (power off first). Contact customer support. |
| Motion sensor not detecting. | Sensor obstructed. Range setting too low. Mounting height incorrect. | Clear any obstructions in front of the sensor. Adjust detection range setting. Ensure mounting height is around 2.5 meters. |
9. Specifications
| Feature | Specification |
|---|---|
| Brand | LUTEC |
| Model Number | 5205702118 |
| Material | Aluminium |
| Color | Anthracite |
| Dimensions (L x W x H) | 16.25 x 18.06 x 16.45 cm |
| Weight | 600 g |
| Power Source | AC (Alternating Current) |
| Voltage | 230 Volts |
| Wattage | 16.1 Watts |
| Luminous Flux | 1100 Lumens |
| Color Temperature | 3000 K (Warm White) |
| Special Feature | Motion Sensor |
| Motion Sensor Angle | 180 degrees |
| Motion Sensor Range | 0-10 meters (at 2.5m mounting height) |
| Timer Setting | 10 seconds to 10 minutes |
| Light Sensitivity | 10 lux |
| IP Rating | IP54 |
| Energy Efficiency Class | F |
Figure 5: Dimensions of the LUTEC Polo LED Outdoor Wall Light (Height: 16.4 cm, Width: 16.2 cm, Depth: 18 cm).
Figure 6: Energy efficiency label for the LUTEC Polo LED Outdoor Wall Light, showing an F rating and 17 kWh/1000h consumption. For more details, visit the EPREL database.
Figure 7: Product data sheet in German, detailing technical specifications and energy consumption for the LUTEC Polo LED Outdoor Wall Light.
10. Warranty and Support
LUTEC products are manufactured to high-quality standards. For warranty information, please refer to the terms and conditions provided at the point of purchase or visit the official LUTEC website. For technical support or inquiries, please contact your retailer or LUTEC customer service.
