NUTOMO Fingerprint Entry Door Handle Lock

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your NUTOMO Fingerprint Entry Door Handle Lock. Please read this manual thoroughly before installation and use to ensure proper function and safety.

The NUTOMO smart lock offers multiple access methods including fingerprint, user passcode, IC card, and traditional physical keys, providing enhanced security and convenience for your home, hotel, or office.

2. Safety Information

• Do not attempt to disassemble or repair the lock yourself. Contact customer support for assistance.
• Use only specified batteries (4 AA batteries). Do not mix old and new batteries or different types of batteries.
• Keep physical keys in a secure location outside the property.
• Avoid exposing the lock to direct sunlight or extreme temperatures for prolonged periods.
• Ensure the door frame and door are properly aligned and free of obstructions for smooth operation.

3. Package Contents

Verify that all components are present before beginning installation:

• Front Panel Assembly (with keypad and fingerprint sensor)
• Back Panel Assembly (with battery compartment)
• Latch Mechanism
• Strike Plate
• Mounting Screws and Hardware
• Physical Keys (2)
• IC Cards (2)
• User Manual
• Installation Template

Note: 4 AA batteries are required but not included.

4. Setup and Installation

4.1 Door Preparation

Ensure your door meets the following specifications:

• Door thickness: 1.49-2.36 inches (38-60 mm)
• Backset: 2-3/8 inches or 2-3/4 inches (60mm or 70mm)

If replacing an existing lock, ensure the door holes are compatible. If the door has two holes, you may need to seal one or use a deadbolt in conjunction with this lock if the holes are too close.

4.2 Latch Installation

Adjust the latch length if necessary and install it into the door edge. Secure with screws.

4.3 Handle Direction Adjustment

The handle direction can be adjusted for left-hand or right-hand doors. Turn the front handle to the Left and the back handle to the Right for a left-hand door. For a right-hand door, turn the front handle to the Right and the back handle to the Left.

4.4 Front Panel and Mounting Plate Installation

Install the front panel, routing the IC wire under the latch. Then, install the mounting plate and connect the IC wire.

4.5 Battery Installation

Insert 4 AA batteries into the battery compartment on the back panel. Ensure correct polarity. Close the battery cover securely.

5. Operating Instructions

5.1 Unlocking Methods

• Fingerprint Unlock: Place your registered finger on the sensor.
• Passcode Unlock: Enter your registered passcode followed by '#'.
• IC Card Unlock: Tap your registered IC card on the keypad.
• Physical Key Unlock: Use the provided physical key for manual override.

5.2 Auto-Lock Feature

The lock is equipped with an auto-lock feature that engages after a short period (typically 5 seconds) once the door is closed. This ensures your door is always secured.

5.3 Anti-Peeping Virtual Code

To enhance security, you can enter random digits before or after your actual passcode. This prevents others from guessing your code by observing your finger movements.

5.4 Emergency Power and Key Access

In case of battery depletion, the lock features a USB charging port for emergency power. Additionally, physical keys are provided for manual access.

5.5 Doorbell Function

After waking up the keypad, press '#', and the doorbell will sound three times.

6. Programming and Management

6.1 Setting the Management Passcode

To enter the menu, input "*#". Then, press '1' for Management Setting, and '1' again to set the management passcode. Input your desired code twice, ending with '#'.

6.2 Adding Fingerprints and IC Cards

After setting the management passcode, you can add fingerprints and IC cards. Enter the management menu, select the appropriate option, and follow the voice prompts. For fingerprints, input your finger 5 times. For IC cards, tap the card once.

6.3 Sharing Passcodes

The lock supports up to 300 sets of passwords, allowing you to share access with multiple users.

6.4 Resetting the Lock

To reset the lock to factory settings, remove the battery cover while the lock is powered on. Press and hold the reset button for approximately 5 seconds until you hear "Initializing". Release the button, and the lock will reset.

7. Maintenance

• Battery Replacement: Replace all 4 AA batteries when the low battery alarm sounds.
• Cleaning: Wipe the keypad and fingerprint sensor with a soft, dry cloth. Avoid abrasive cleaners or solvents.
• Environmental Conditions: The lock is designed to withstand temperatures from -13°F to 149°F and has an IP63 rating for dust and water resistance.

8. Troubleshooting

• Lock not responding: Check battery levels. Use emergency USB power or physical key.
• Fingerprint not recognized: Ensure your finger is clean and dry. Try re-registering your fingerprint. Cold weather can sometimes affect fingerprint reader performance; use a passcode or key fob as an alternative.
• Passcode not working: Ensure you are entering the correct passcode followed by '#'. Try resetting the lock if issues persist.
• Auto-lock not engaging: Verify the door is fully closed and aligned.

9. Specifications

10. Warranty and Support

For warranty information, technical support, or any inquiries regarding your NUTOMO Fingerprint Entry Door Handle Lock, please refer to the product packaging or visit the official NUTOMO website. Contact details for customer service are typically provided with your purchase.