Jaronx BMW LED Console Panel Ambient Light User Manual

1. Introduction

This manual provides detailed instructions for the installation, setup, and operation of your Jaronx LED Console Panel Ambient Light. This product is designed to enhance your vehicle's interior aesthetics with dual-color LED lighting for the central console area. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Product Features

• High-Quality Material: Constructed from durable ABS+PC material, ensuring solid and wearable performance.
• Enhanced Interior: The bright black console panel design integrates seamlessly, enhancing the vehicle's interior texture.
• Dual-Color Lighting: Features two selectable colors (blue and orange) that can be adjusted via the iDrive display.
• Adjustable Brightness: Lighting brightness is adjustable through the dimmer on the headlight panel or the iDrive controls.
• Robust Wiring: High-standard wiring is waterproof, fireproof, and resistant to high temperatures.

3. Compatibility

This product is compatible with the following BMW models:

• BMW 3 Series (F30, F31)
• BMW 4 Series (F32, F33)

Please ensure your vehicle has a 3-pin wiring connector for the console panel. This product is not suitable for 4-pin vehicles.

4. Package Contents

The package typically includes:

• Jaronx LED Console Panel Ambient Light (Gross Black)
• Necessary wiring harness and connectors
• Installation tools (e.g., pry tool, screwdriver)

5. Installation Instructions

5.1. General Safety Precautions

• Ensure the vehicle is turned off and the ignition is disengaged before starting installation.
• Use appropriate tools to avoid damaging vehicle interior components.
• If unsure about any step, consult a professional installer.

5.2. Console Panel LED Lighting Installation

This section guides you through installing the LED ambient light on your central console panel.

1. Carefully pry open the central control trim panel using a plastic pry tool.
2. Loosen the screws securing the CD panel.
3. Gently pull out the CD panel and disconnect the original wiring harness.
4. Remove the old CD panel from its housing.
5. Replace the old CD panel with the new ambient light panel.
6. Connect the new ambient light's wiring to the original car's plug. Ensure a secure connection.
7. Install the four screws to secure the CD panel.
8. Pull off the plug connection for the small trim panel and plug in the original ambient lamp plug.
9. Reinstall the central control trim panel, ensuring all clips are securely fastened.

Image: Console panel showcasing both red and blue ambient lighting options.

Image: Close-up of the 3-pin wiring connector, indicating compatibility.

5.3. Door Panel Ambient Light Installation

This section outlines the process for installing ambient lights within the door panels.

1. Use a tool to pry open the inner door handle and unscrew the screws at both ends.
2. Carefully remove the door panel.
3. Cut off the original buckle of the door panel.
4. Remove any small plugs as necessary.
5. Cut off the two small buckles and remove the original car trim.
6. Replace with new LED decorative light strips, threading them into position.
7. Install the small screws to fix the position of the new light strips.
8. Install the larger screws in the middle row to secure the light strips.
9. Connect the three-wire plug for the new ambient light.
10. Tape the plugs of the two wires to the door panel to secure them.
11. If applicable, remove the lifter button from the lifter harness for better insertion of wiring.
12. Reinstall the door panel, ensuring all connections are secure and the panel is properly seated.

5.4. Gear Shift Knob Cover Installation

This section details how to install a new gear shift knob cover.

1. Carefully pry off the existing gear shift knob cover using a plastic pry tool.
2. Remove the old cover completely.
3. Align the new gear shift knob cover with the shifter.
4. Press firmly until it snaps into place, ensuring a secure fit.

5.5. Dashboard Panel Trim Installation

This section provides instructions for installing the dashboard panel trim.

1. Clean the surface of the dashboard where the trim will be applied.
2. Remove the adhesive protective film from the trim piece.
3. Start at the bottom edge, carefully positioning the trim.
4. Use a small scraper to press the edges into the gap and scrape until it fits snugly.

5.6. Center Console Multimedia Panel Trim Installation

This section guides you through installing the center console multimedia panel trim.

1. Clean the surface of the multimedia panel area.
2. Remove the adhesive protective film from the trim piece.
3. Carefully align and position the trim over the multimedia panel.
4. Press firmly to ensure proper adhesion and a secure fit.

6. Setup & Operating

6.1. Color Selection

The LED ambient lights offer two colors: blue for Sport mode and orange for Classic mode. These colors can be changed through your vehicle's iDrive display settings.

Image: Display of Sport (blue) and Classic (orange) ambient light modes.

6.2. Brightness Adjustment

The brightness of the ambient light is adjustable. You can control it through the dimmer switch located on the headlight panel or directly via the iDrive controls on the center screen.

7. Maintenance

To maintain the appearance and functionality of your Jaronx LED Console Panel Ambient Light, follow these simple guidelines:

• Regularly wipe the panel with a soft, damp cloth to remove dust and fingerprints.
• Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish.
• Ensure no liquids seep into the LED strips or wiring during cleaning.

8. Troubleshooting

8.1. No Sound Issue (for multimedia systems)

If you encounter a 'no sound' issue after installing a new multimedia screen, follow these steps:

1. Access the OEM system on your screen. If it doesn't display properly, contact customer service.
2. Navigate to Multimedia > External Devices.
3. Check if OEM Bluetooth is selected. If so, go to Settings > System to turn off the 'Use Car's BT Channel' feature.
4. Disconnect your phone's original Bluetooth connection from the car.
5. After disconnecting, go to the car's settings and select 'Auto Switch to AUX' feature off.
6. Return to the original car interface, select 'AUX front'.
7. If there is still no sound, first adjust the volume knob.
8. If the issue persists, connect the AUX harness.
9. Check the AB ground plugs and disconnect/reconnect them if they are connected/disconnected incorrectly.
10. Check if there is a fiber optic cable in the OEM ISO harness. If so, adapt it to the PEMP ISO harness.
11. Finally, ensure the power cable and LVDS on the back of the machine are not loose. If they are, re-plug them once.

8.2. Lights Not Changing Color

If the ambient lights are not changing colors as expected via the iDrive system:

• Verify that the correct lighting mode (Sport/Classic) is selected in the iDrive display.
• Ensure all wiring connections are secure and properly seated. A loose connection can prevent proper signal transmission.
• Check the dimmer settings on both the headlight panel and iDrive; sometimes brightness settings can affect perceived color changes.
• If the issue persists, consult the vehicle's original manual for ambient lighting settings or contact Jaronx customer support.

9. Specifications

• Brand: Jaronx
• Model: Ambient Light LED Lighting
• Material: Acrylonitrile Butadiene Styrene (ABS)
• Color Options: Blue, Orange
• Light Source Type: LED
• Voltage: 12 Volts
• Auto Part Position: Center Console
• Fit Type: Vehicle Specific Fit (BMW 3 Series F30 F31, 4 Series F32 F33)
• Special Feature: Waterproof
• Item Weight: 0.31 Kilograms (approx. 10.8 ounces)

10. Warranty and Support

For warranty information and technical support, please refer to the product packaging or contact the seller directly. Keep your purchase receipt as proof of purchase.