VICTGOAL HT-23

Download PDF
Contents

VICTGOAL Bike Helmet with LED Rear Light (Model HT-23) Instruction Manual

Introduction

This manual provides essential information for the proper use, adjustment, and maintenance of your VICTGOAL Bike Helmet (Model HT-23). Please read these instructions carefully before using your helmet to ensure maximum safety and comfort. This helmet is designed for cycling activities and features an integrated LED rear light, magnetic goggles, and a sun visor.

Product Features

  • Rechargeable LED Rear Light: Enhances visibility with three lighting modes: steady, fast flashing, and slow flashing. Charges via USB and provides up to 10 hours of use.
  • Cool and Lightweight Design: Features 21 breathable vents to reduce air resistance and maintain comfort during rides. Weighs approximately 310g (0.68 lb).
  • Impact Resistance: Constructed with a high-density PC shell and EPS foam to absorb impact and provide comprehensive protection.
  • Magnetic Goggles and Visor: Includes a detachable magnetic goggle and a sun visor. The goggle protects eyes from sunlight, wind, and debris, and can be worn with prescription glasses.
  • Adjustable Fit System: Equipped with an adjustable dial for a secure and comfortable fit for various head sizes. Available in M, L, and XL.

Setup and Installation

1. Adjusting Helmet Fit

Proper fit is crucial for helmet safety. The helmet should sit level on your head, covering your forehead, and should not move excessively when shaken.

  1. Place the helmet on your head.
  2. Locate the adjustment dial at the back of the helmet.
  3. Turn the dial clockwise to tighten the fit or counter-clockwise to loosen it until the helmet feels snug but comfortable.
  4. Adjust the side straps so they form a 'V' shape just below your ears.
  5. Fasten the chin strap buckle and tighten it so that no more than two fingers can fit between the strap and your chin.
Rear view of VICTGOAL bike helmet showing the adjustable size regulator dial.

Image: Rear view of the helmet with the adjustable size regulator.

2. Attaching the Sun Visor

The sun visor can be attached to the front of the helmet to provide shade.

  1. Align the three pins on the visor with the corresponding slots on the helmet.
  2. Gently push the pins into the slots until they snap securely into place.
  3. To remove, carefully pull the visor away from the helmet at each pin location.

3. Attaching Magnetic Goggles

The magnetic goggles attach to the helmet for eye protection.

  1. Hold the goggles near the front of the helmet.
  2. The magnets will automatically align and secure the goggles to the helmet.
  3. To remove, gently pull the goggles away from the helmet.
A person demonstrating how to attach the magnetic goggles to the VICTGOAL bike helmet.

Image: Attaching the magnetic goggles to the helmet.

4. Charging the LED Rear Light

The integrated LED rear light is rechargeable via USB.

  1. Locate the USB charging port on the rear light unit.
  2. Connect the provided USB cable to the port and to a standard USB power source (e.g., computer, wall adapter).
  3. The indicator light will show charging status (e.g., red for charging, green/blue for fully charged).
  4. A full charge typically takes approximately 2 hours.
Diagram showing the USB charging port and different usage times for the VICTGOAL helmet's LED light modes.

Image: USB charging port and LED light usage times.

Operation

1. Using the LED Rear Light

Press the power button on the LED light unit to cycle through the three lighting modes:

  • Steady: Constant illumination for continuous visibility.
  • Fast Flashing: Rapid flashing for increased attention.
  • Slow Flashing: Slower flashing pattern for varied visibility needs.

Press and hold the button to turn the light off.

Video: Demonstration of the VICTGOAL Bike Helmet with Visor and Goggles, including LED light operation.

2. Using Goggles and Visor

The magnetic goggles provide protection from sun, wind, and debris. They are designed to fit over most prescription glasses. The sun visor offers additional shade.

VICTGOAL bike helmet shown with both the sun visor and magnetic goggles attached, highlighting UV400 protection.

Image: Helmet with visor and goggles, illustrating UV400 protection.

Sizing and Fit Guide

To determine your correct helmet size, measure the circumference of your head approximately 0.6 inch (1.5 cm) above your ears and across your forehead.

SizeHead CircumferenceRecommended For
M54-58 cm (21.3-22.8 inches)Teenagers / Adults with Small Head Size
L57-61 cm (22.4-24 inches)Adult Men and Women
XL59-63 cm (23.2-24.8 inches)Adults with Large Head Size

Recommendation: If your head measurement falls between two sizes, choose the larger size for a more comfortable fit.

Sizing guide for VICTGOAL bike helmet M size for teenagers and adults with small head size (54-58cm).

Image: Sizing guide for Medium helmet.

Sizing guide for VICTGOAL bike helmet L size for adult men and women (57-61cm).

Image: Sizing guide for Large helmet.

Sizing guide for VICTGOAL bike helmet XL size for adults with large head size (59-63cm).

Image: Sizing guide for Extra Large helmet.

Maintenance

1. Cleaning the Helmet

Regular cleaning helps maintain hygiene and extends the helmet's lifespan.

  • The inner liner is soft and washable. Detach it from the helmet for cleaning.
  • Wash the liner by hand with mild soap and water. Allow it to air dry completely before reattaching.
  • Wipe the outer shell with a damp cloth and mild soap. Avoid harsh chemicals or abrasive cleaners.
Close-up view of the helmet's interior padding and adjustment system, highlighting ventilation.

Image: Interior padding and adjustment system.

2. LED Light Care

  • Ensure the USB charging port cover is securely closed when not charging to prevent moisture ingress.
  • Charge the LED light regularly, especially if the helmet is stored for extended periods, to maintain battery health.

Troubleshooting

  • Helmet feels loose or too tight: Re-adjust the rear dial and chin straps as described in the "Adjusting Helmet Fit" section.
  • LED Rear Light not turning on: Ensure the light is fully charged. If the issue persists, contact customer support.
  • Goggles/Visor not attaching securely: Check for any obstructions on the magnetic points or pins. Ensure they are clean and properly aligned.

Specifications

FeatureDetail
BrandVICTGOAL
Model NumberHT-23 (VA112)
Material (Outer)Polycarbonate (PC)
Material (Inner)Expanded Polystyrene (EPS)
WeightApproximately 10.88 ounces (310g)
Ventilation21 Air Vents
Special FeaturesAdjustable Strap, Rechargeable LED Rear Light, Magnetic Goggles, Sun Visor
Included ComponentsHelmet, Magnetic Goggle, Sun Visor

Warranty and Support

The VICTGOAL Bike Helmet (Model HT-23) comes with a 1-Year Warranty from the date of purchase, covering manufacturing defects. For warranty claims, technical support, or any questions regarding your helmet, please contact VICTGOAL customer service through the retailer where the product was purchased or visit the official VICTGOAL website for contact information.

Always retain your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.