Introduction
Thank you for choosing the LUTEC Try Solar LED Wall Lamp. This manual provides essential information for the safe and efficient use of your new solar-powered outdoor light. Please read these instructions carefully before installation and retain them for future reference.
Image: The LUTEC Try Solar LED Wall Lamp, model 6939101330, providing bright illumination on an outdoor wall.
Safety Information
- Ensure the mounting surface is stable and can support the weight of the lamp.
- Do not attempt to disassemble or modify the lamp, as this may void the warranty and pose a safety risk.
- Keep the solar panel clean to ensure optimal charging performance.
- This product is designed for outdoor use and is weather-resistant (IP54). However, avoid submerging it in water.
- Dispose of batteries according to local regulations.
Product Overview
The LUTEC Try Solar LED Wall Lamp is a modern outdoor lighting solution featuring an integrated solar panel, rechargeable battery, and motion sensor. It is constructed from durable plastic and designed for easy installation without the need for external wiring.
Key Features:
- Solar Powered: Integrated solar panel charges the internal battery during the day.
- Motion Sensor: Detects movement to activate lighting modes.
- Weather Resistant: IP54 rating ensures protection against dust and splashing water.
- Multiple Lighting Modes: Adjustable via a switch on the back.
- Light Output: 8W LED, 4000K color temperature, 500 lumens.
Dimensions:
- Length: 12.5 cm
- Width: 12.5 cm
- Height: 23.1 cm
- Protrusion from wall: 6.9 cm
- Weight: 320 g
Image: Detailed view of the lamp's dimensions and components including the solar panel, motion sensor, and opal PC diffuser.
Setup and Installation
The LUTEC Try lamp is designed for straightforward installation. No electrical wiring is required.
Package Contents:
- LUTEC Try Solar LED Wall Lamp
- Mounting hardware (screws and wall plugs)
- Instruction Manual
Installation Steps:
- Choose a Location: Select an outdoor location where the solar panel can receive direct sunlight for at least 6-8 hours daily to ensure optimal charging. The lamp is suitable for gardens, doorways, terraces, and hallways.
- Mark Drilling Points: Use the lamp's mounting plate as a template to mark the drilling points on the wall.
- Drill Holes: Drill holes at the marked points and insert the wall plugs.
- Mount the Lamp: Align the lamp with the drilled holes and secure it with the provided screws. Do not overtighten.
- Select Operating Mode: Before final tightening, select your desired operating mode using the switch located on the backside of the lamp (see "Operating Instructions" section).
Image: The LUTEC Try lamp installed outdoors, showcasing its suitability for various exterior environments.
Operating Instructions
The LUTEC Try lamp features a multi-function switch on its backside to select between three lighting modes:
- ON Mode: The lamp will stay on continuously at 10% brightness (50 lumens) during darkness.
- AUTO Mode: The lamp remains off until motion is detected. Upon detection, it illuminates at 100% brightness (500 lumens) for approximately 30 seconds, then turns off. This mode activates only in darkness.
- DIM Mode: The lamp stays on at a very low brightness (2 lumens) during darkness. When motion is detected, it switches to 100% brightness (500 lumens) for approximately 30 seconds, then returns to dim brightness.
The motion sensor has a 120-degree sensing angle and a maximum sensing range of 10 meters.
Image: Visual representation of the ON, AUTO, and DIM lighting modes and their behavior.
Image: Illustration of the motion sensor's detection capabilities, including its 120-degree angle and 10-meter range.
Maintenance
- Cleaning: Regularly wipe the solar panel and light diffuser with a soft, damp cloth to remove dust, dirt, or debris. A clean solar panel ensures efficient charging.
- Battery: The lamp contains a replaceable Lithium-Ion battery. If the lamp's performance significantly degrades over time, the battery may need replacement. Contact customer support for guidance on battery replacement.
- Inspection: Periodically check the mounting screws to ensure the lamp remains securely attached to the wall.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on at night. |
|
|
| Motion sensor not detecting movement. |
|
|
| Lamp light is dim or flickers. |
|
|
Specifications
| Feature | Detail |
|---|---|
| Model Number | 6939101330 |
| Brand | LUTEC |
| Power Source | Solar Energy |
| Light Source | Integrated LED |
| Wattage | 8 W |
| Luminous Flux | 500 lm (max) |
| Color Temperature | 4000 K |
| Motion Sensor | 120° sensing angle, Max. 10m sensing range |
| Battery | 1 Lithium Ion (included, replaceable) |
| Material | Plastic (with aluminum elements) |
| Protection Rating | IP54 (Dust and splash water protected) |
| Dimensions (L x W x H) | 12.5 cm x 12.5 cm x 23.1 cm |
| Weight | 320 g |
| Operating Modes | ON, AUTO, DIM |
Warranty and Support
The LUTEC Try Solar LED Wall Lamp comes with a 2-year warranty. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or inquiries regarding replacement parts (e.g., battery), please contact your retailer or LUTEC customer service. Refer to the contact information provided with your purchase or visit the official LUTEC website.
Manufacturer: LUTEC
Country of Origin: Germany
