Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Tedeligo Wireless RF 433 MHz Switch Kit. This kit allows for convenient remote control of lighting and other electrical appliances without the need for complex wiring or Wi-Fi connectivity. Please read this manual carefully before installation and use to ensure safe and optimal performance.
Image: Wireless control setup in a living room, demonstrating the ease of use without visible wires.
Setup Instructions
1. Wiring the Receiver
The receiver unit connects between your power source and the appliance you wish to control. It is designed for easy installation using terminal blocks, eliminating the need for a screwdriver for connections. Ensure the power supply is disconnected before performing any wiring.
- Connect the live (L) and neutral (N) wires from your power source to the 'Input' terminals of the receiver.
- Connect the live (L) and neutral (N) wires of your appliance (e.g., light fixture) to the 'Output' terminals of the receiver.
Image: Detailed wiring diagram for connecting the receiver to power and a light fixture.
2. Pairing the Wireless Switch with the Receiver
The switch and receiver are typically pre-paired. If re-pairing is needed or for adding additional switches/receivers, follow these steps:
- To Pair: Press the learning button on the receiver two times quickly. The indicator light on the receiver will flash.
- Within 10 seconds, press the desired button on the wireless switch two times. The receiver's indicator light will flash rapidly and then turn off, indicating successful pairing.
Press receiver button 2 times
Press switch button 2 times
3. Clearing Pairing Information
To clear all paired switches from a receiver:
- Press the learning button on the receiver eight times quickly. The indicator light will flash rapidly and then turn off, indicating all pairing information has been cleared.
Image: Clearing pairing by pressing the receiver button 8 times.
4. Mounting the Wireless Switch
The wireless switch offers flexible installation options:
- Double-sided Tape: Use the included double-sided adhesive tape to fix the switch to any smooth, clean surface.
- Screws: For a more permanent installation, use the included screws and expansion plugs to mount the switch base to a wall.
Mounting with double-sided tape
Mounting with expansion screws
Operating Instructions
1. Basic Operation
Once the receiver is wired and paired with the wireless switch, simply press the button on the switch to toggle the connected appliance ON or OFF. The switch can be used while mounted or removed from its base for portable remote control.
2. Multi-Control Functionality
The Tedeligo Wireless Switch Kit supports flexible multi-control configurations:
- Multiple Switches, One Receiver: You can pair up to 24 wireless switches with a single receiver to control the same light or appliance from various locations (e.g., controlling a staircase light from multiple floors).
- One Switch, Multiple Receivers: A single wireless switch can control up to 24 receivers simultaneously, allowing you to control multiple lights or appliances with one press.
Multiple switches controlling one light
One switch controlling multiple devices
Maintenance
1. Battery Replacement (Wireless Switch)
The wireless switch is powered by a 27A12V alkaline battery, which has a lifespan of over 7,000 uses. When the switch's performance degrades or it stops responding, it may be time to replace the battery.
- Carefully open the wireless switch casing.
- Remove the old 27A12V battery.
- Insert a new 27A12V alkaline battery, ensuring correct polarity.
- Close the switch casing securely.
2. Cleaning
To clean the switch and receiver units, use a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Appliance does not respond to switch. |
|
|
| Switch requires multiple presses to activate. |
|
|
| Switch stopped working after some time. |
|
|
Specifications
| Brand | Tedeligo |
| Model Reference | 2201E |
| Material | Plastic |
| Operating Voltage | 240 Volts (AC) |
| Current Rating | 10 A |
| Power | 2300 Watts |
| RF Frequency | 433 MHz |
| Control Range | Up to 30 meters indoors, 100 meters outdoors |
| Switch Type | Push-button, 1-way |
| Electrical Plug Type | Wall mount |
| IP Rating | IPX7 |
| Switch Battery | 1 x 12V (27A type), Alkaline (included) |
| Package Dimensions | 10.3 x 9.2 x 4.2 cm; 120 grams |
Warranty and Support
This product has passed CE and FCC verification, ensuring compliance with relevant safety and quality standards.
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly through your purchase platform. Please retain your proof of purchase for warranty purposes.
