Introduction
Thank you for choosing the Faber HOOD ZEST HC SC FL BK 60 Kitchen Chimney. This appliance is designed to provide efficient ventilation and maintain a clean kitchen environment. This manual contains important information regarding the installation, operation, maintenance, and safety of your chimney. Please read it thoroughly before use and retain it for future reference.
Image: Front view of the Faber HOOD ZEST HC SC FL BK 60 Kitchen Chimney.
Safety Information
Always adhere to the following safety precautions to prevent injury or damage to the appliance:
- Ensure the power supply matches the voltage specified on the rating label.
- Installation must be performed by a qualified technician.
- Do not operate the chimney without the oil collector properly installed.
- Clean the oil collector regularly to prevent grease buildup, which can be a fire hazard.
- Keep children away from the appliance during operation and cleaning.
- Do not flambé under the chimney.
- Ensure adequate ventilation in the room when the chimney is used simultaneously with gas or other fuel-burning appliances.
- Disconnect the power supply before any cleaning or maintenance.
Product Features and Components
The Faber HOOD ZEST HC SC FL BK 60 chimney incorporates advanced features for user convenience and efficient performance.
- Filterless Technology: Eliminates the need for traditional filters, simplifying maintenance.
- Heat Auto-Clean: An automated cleaning function that melts and collects oil residues.
- Touch & Gesture Control: Intuitive controls for fan speed, lighting, and auto-clean activation.
- LED Lights: Energy-efficient illumination for your cooking area.
- Oil Collector: Detachable tray for easy disposal of collected oil.
Image: Detailed view of the control panel highlighting filterless design, gesture and touch control, smart LED lights, and suction power.
Image: Diagram illustrating the filterless technology, showing smoke and oil being drawn into the chimney.
Setup and Installation
Proper installation is crucial for the optimal performance and safety of your chimney. It is strongly recommended that installation be carried out by a certified Faber service technician.
Installation Guidelines:
- Ensure the chimney is mounted at the recommended height above the cooking surface (typically 65-75 cm for gas hobs and 60-70 cm for electric hobs).
- The chimney requires a dedicated power outlet.
- For ducted/vented operation, ensure the ducting is correctly installed and sealed to prevent air leakage.
- Verify that all mounting brackets are securely fastened to a sturdy wall structure.
For installation assistance, please contact Faber customer service at 1800-209-3484.
Image: Side view of the Faber chimney, showing its wall-mounted design.
Operating Instructions
Your Faber chimney features both touch and gesture controls for ease of use.
Touch Controls:
- Power On/Off: Press the power icon to turn the chimney on or off.
- Fan Speed Adjustment: Use the '1', '2', '3' buttons to select desired suction speed. '1' is low, '3' is high.
- Light Control: Press the light bulb icon to turn the LED lights on or off.
- Auto-Clean Activation: Press the auto-clean icon (often represented by a water droplet or steam symbol) to initiate the heat auto-clean cycle.
Gesture Controls:
The chimney is equipped with a motion sensor for hands-free operation.
- Power On/Off: Wave your hand from left to right in front of the sensor to turn the chimney on or off.
- Increase/Decrease Fan Speed: Wave your hand from right to left to increase fan speed, and from left to right to decrease fan speed.
Image: Close-up of the touch control panel with icons for power, fan speeds, light, and auto-clean.
Image: Diagram illustrating the motion sensor for gesture control, showing hand movements to adjust settings.
Maintenance
Regular maintenance ensures the longevity and efficiency of your Faber chimney.
Heat Auto-Clean Function:
- Activate the auto-clean function weekly or bi-weekly, depending on cooking frequency.
- During the auto-clean cycle, the heating element melts accumulated oil, which then drips into the oil collector.
- The cycle typically lasts for a set duration, after which the chimney will automatically switch off or return to standby.
Cleaning the Oil Collector:
- The oil collector is located at the bottom of the chimney.
- Carefully slide out the oil collector once it is full or after an auto-clean cycle.
- Empty the collected oil and wash the collector with warm, soapy water. Rinse thoroughly and dry before reinserting.
- Ensure the oil collector is securely in place before operating the chimney.
Exterior Cleaning:
- Wipe the exterior surfaces with a soft, damp cloth and mild detergent.
- Avoid abrasive cleaners or harsh chemicals that can damage the finish.
- For the curved glass, use a glass cleaner and a soft cloth to avoid streaks.
Image: Diagram illustrating the auto-clean process, showing oil dripping into the collector.
Troubleshooting
Refer to this section for solutions to common issues. If the problem persists, contact customer service.
| Problem | Possible Cause | Solution |
|---|---|---|
| Chimney not turning on. | No power supply; loose connection. | Check power plug and circuit breaker. Ensure connections are secure. |
| Low suction power. | Oil collector full; ducting obstruction; incorrect installation height. | Empty and clean oil collector. Check ducting for blockages. Verify installation height. |
| Unusual noise during operation. | Loose components; motor issue. | Ensure all parts are securely fastened. If noise persists, contact service. |
| Auto-clean not functioning. | Sensor malfunction; electrical issue. | Ensure no obstructions near sensors. Contact service if problem continues. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | HOOD ZEST HC SC FL BK 60 |
| Type | Curved glass, Wall mounted, Heat Auto-Clean |
| Size | 60 cm |
| Suction Capacity | 1200 m³/hr |
| Control Type | Touch and Gesture |
| Max Noise Level | 59 Decibels |
| Light Source | LED (2 x 1.5 watt) |
| Filter Type | Filterless Technology |
| Material Type | Black finish with curved glass |
| Product Dimensions (D x W x H) | 48D x 60W x 54H Centimeters |
| Voltage | 220 Volts |
| Item Weight | 11000 Grams |
Image: Diagram showing the dimensions of the Faber HOOD ZEST HC SC FL BK 60 chimney (600mm width, 480mm depth, 540mm height).
Warranty and Support
Your Faber HOOD ZEST HC SC FL BK 60 Kitchen Chimney comes with a comprehensive warranty and dedicated customer support.
- Warranty: 1 Year comprehensive warranty on the product & 5 years on the motor.
- Manufacturer: Franke Faber India Pvt Ltd
- Customer Service: For installation, service, or any queries, please contact 1800-209-3484.
Please retain your purchase invoice for warranty claims.