MAIDeSITe SN1 Electric Standing Desk (100 x 60 cm) User Manual

Introduction

Thank you for choosing the MAIDeSITe SN1 Electric Standing Desk. This manual provides detailed instructions for the assembly, operation, and maintenance of your new ergonomic workspace. Please read this manual thoroughly before use to ensure proper function and safety.

The MAIDeSITe SN1 Electric Standing Desk in a typical home office setup.

Safety Information

To prevent injury or damage, please observe the following safety guidelines:

• Ensure all components are securely fastened before use.
• Do not exceed the maximum load capacity of 80 kg.
• Keep children and pets away from the desk during operation.
• The desk features an anti-collision system. However, always ensure the path of movement is clear of obstacles.
• Do not attempt to modify the desk's electrical or mechanical components. Contact customer support for assistance.
• Disconnect power before cleaning or maintenance.

The anti-collision system automatically stops movement when an obstacle is detected.

Assembly Instructions

The MAIDeSITe SN1 desk is designed for easy assembly. All necessary tools are included. Follow these steps carefully:

Step 1: Attach the Lifting Columns to the Crossbar

Connect the two lifting columns to the central crossbar. Ensure the driving rod is correctly inserted and secured. Use the provided M6*8 Hexagon Screws (x4) and M4 Allen Wrench (x1) to fasten the components.

Step 2: Install the Side Brackets

Attach the side brackets to the top of the lifting columns. Secure them using the M6*35 Hexagon Screws (x8), Washers (x8), and M4 Allen Wrench (x1).

Step 3: Secure the Desktop

Place the desktop upside down on a soft, clean surface. Align the pre-drilled holes with the frame. Use the M6*16 Hexagon Screws (x6) and M4 Allen Wrench (x1) to attach the desktop to the frame.

Step 4: Install the Control Box and Control Panel

Mount the control box and control panel to the underside of the desktop using the ST5*0.8*16 Tapping Screws (x2) and Screwdriver (x1).

Step 5: Connect Cables

Connect all cables from the lifting columns and control panel to the control box. Ensure all connections are firm.

Step 6: Install Accessories

Attach the hook, wire management tray, and felt side storage bag using the provided M6*14 Hexagon Screws (x10), M6 Nuts (x6), and M4 Allen Wrench (x1). For the memo board, simply place it on the desktop.

The desk is designed for quick assembly with clear instructions and included tools.

Step 7: Choose Feet or Casters

You can choose between fixed feet or 360-degree swivel casters for mobility. Install your preferred option using the M14 Open End Wrench (x1).

Switch between fixed feet and movable casters as needed.

Operating Instructions

Height Adjustment

The desk's height can be adjusted electrically from 72 cm to 120 cm. Use the Up (▲) and Down (▼) buttons on the control panel to move the desktop to your desired height.

The desk offers a wide height adjustment range for sitting and standing positions.

Control Panel Functions

• Up (▲) / Down (▼): Adjusts the desk height.
• Memory Presets (1, 2, 3, 4): Save and recall preferred height settings. To save a height, adjust the desk to the desired level, then press 'M' followed by the desired number (1-4). To recall, simply press the corresponding number.
• USB Charging Port: Located on the control panel for convenient charging of devices.
• Child Safety Lock: Activates to prevent accidental height adjustments. Consult the full manual for specific activation/deactivation steps.
• Anti-Collision System: Automatically stops and slightly reverses the desk's movement if an obstruction is detected during height adjustment.

Easily save and recall your preferred sitting and standing heights with the memory presets.

The control panel features an LED display, touch screen buttons, and a USB charging port.

Reset Procedure

1. Long press the Down (▼) key until the desktop reaches its lowest position.
2. Long press the Down (▼) key again. The digital display will show "RST". The desk is now in initialization mode.
3. Release the Down (▼) key when the buzzer rings. The initialization is complete, and the display will show the current height.

Maintenance

• Regularly check all screws and connections to ensure they are tight.
• Clean the desktop surface with a soft, damp cloth. Avoid harsh chemicals.
• Keep the lifting columns free from dust and debris to ensure smooth operation.
• Do not place hot items directly on the desktop without protection.

Troubleshooting

If you encounter any issues with your MAIDeSITe SN1 desk, please refer to the following common solutions:

• Desk not moving: Check all cable connections. Ensure the power cord is securely plugged into both the desk and the wall outlet. Perform a reset procedure.
• Uneven movement: Perform a reset procedure to re-synchronize the lifting columns.
• Error code on display: Refer to the full product manual for a list of error codes and their meanings, or contact customer support.
• Anti-collision system too sensitive/not sensitive enough: The sensitivity of the anti-collision system may be adjustable. Consult the full manual or customer support for instructions.

If the problem persists, please contact MAIDeSITe customer support for further assistance.

Specifications

Key specifications highlighting the desk's performance and features.

The desktop is designed to be durable, scratch-resistant, and waterproof.

Warranty and Support

The MAIDeSITe SN1 Electric Standing Desk comes with a 5-year warranty, ensuring peace of mind regarding its quality and durability. For any questions, technical assistance, or warranty claims, please contact MAIDeSITe customer support. Our dedicated support team is available 24/7 to assist you.

You can find contact information on the MAIDeSITe official website or through your purchase platform.