1. Introduction and Overview
This manual provides detailed instructions for the EBL 907 LCD AA/AAA Rechargeable Battery Charger and the accompanying 8-pack of 1100mAh Ni-MH AAA rechargeable batteries. This system is designed for efficient and safe charging of compatible batteries, offering a sustainable power solution for various electronic devices.
Key Features:
- Individual charging slots for 1, 2, 3, or 4 Ni-MH/Ni-CD AA/AAA rechargeable batteries.
- Includes 8 high-capacity 1100mAh Ni-MH AAA rechargeable batteries with Procyco 1200 Tech, supporting up to 500 deep charging/discharging cycles.
- Smart LCD display for each slot, showing individual charging progress. The battery icon stops flashing when fully charged.
- Advanced MCU control and -∆V function for optimized charging.
- Integrated safety features: over-heat protection, over-current protection, short-circuit protection, and detection for non-rechargeable or defective batteries.
- Worldwide compatibility with 100-240V AC, 50/60 Hz input.
Figure 1: EBL 907 LCD AA/AAA Rechargeable Battery Charger with included AAA batteries.
2. Setup Instructions
- Unpack the Charger and Batteries: Carefully remove the EBL 907 charger and the 8 AAA rechargeable batteries from their packaging.
- Inspect the Charger: Ensure the charger is free from any visible damage. The foldable AC plug is located on the back of the unit.
- Insert Batteries: Insert 1 to 4 compatible Ni-MH/Ni-CD AA or AAA rechargeable batteries into the charging slots. Ensure correct polarity (+ and - ends) as indicated on the charger and batteries. The charger supports individual charging, so you can charge any number of batteries from one to four.
- Connect to Power: Extend the foldable AC plug and plug the charger directly into a standard wall outlet (100-240V AC). The LCD display will illuminate, showing the current charge status of each inserted battery.
Figure 2: Proper insertion of batteries into the EBL 907 charger, highlighting individual slots.
Figure 3: Detailed view of the LCD display and battery contact points.
3. Operating Instructions
The EBL 907 charger features an intelligent LCD display that provides real-time feedback on the charging status of each battery.
- Charging Indication: Once plugged in with batteries inserted, the LCD screen will show individual battery icons. These icons will flash to indicate that charging is in progress.
- Full Charge Indication: When a battery is fully charged, its corresponding icon on the LCD display will stop flashing and remain solid.
- Error Detection: If a non-rechargeable or defective battery is inserted, the LCD will display an "ERROR" message for that specific slot. Remove the problematic battery immediately.
- Charging Time: Charging times vary depending on the battery capacity and discharge level. For the included 1100mAh AAA batteries, a full charge typically takes a few hours.
Video 1: Review of the EBL Compact Wall Outlet Battery Charger, demonstrating its features and ease of use.
Video 2: Demonstration of the EBL Charger in use, including charging time review and LCD display functionality.
4. Maintenance
- Cleaning: Disconnect the charger from the power outlet before cleaning. Use a dry, soft cloth to wipe the charger and battery contacts. Do not use abrasive cleaners or immerse the charger in water.
- Storage: Store the charger and batteries in a cool, dry place away from direct sunlight and extreme temperatures. For long-term storage, it is recommended to charge batteries to about 50% capacity.
- Battery Care: Avoid fully discharging Ni-MH batteries frequently, as this can reduce their lifespan. Recharge them when they are low, rather than completely depleted.
5. Troubleshooting
- Batteries Not Charging:
- Ensure batteries are inserted with correct polarity.
- Check if the charger is securely plugged into a working power outlet.
- Verify that the batteries are rechargeable Ni-MH or Ni-CD types. The charger is not compatible with alkaline or lithium batteries.
- If an "ERROR" message appears, the battery may be defective or incompatible. Remove and replace it.
- Slow Charging:
- Ensure the charger is not in an excessively hot environment, which can affect charging efficiency.
- Check the battery capacity; higher capacity batteries will naturally take longer to charge.
- Charger Overheating:
- Disconnect the charger immediately. Allow it to cool down.
- Ensure adequate ventilation around the charger during operation.
6. Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 5.12 x 3.15 x 2.68 inches (3.15"D x 5.12"W x 2.68"H) |
| Item Weight | 8.1 ounces |
| Input Voltage | 100-240V AC, 50/60 Hz, 500mA Max |
| Output Voltage | 1.2 Volts |
| Output Current (AA) | 1x AA 1.2VDC 1800mA, 2x AA 1.2VDC 900mA, 3x AA 1.2VDC 500mA, 4x AA 1.2VDC 500mA |
| Output Current (AAA) | 1x AAA 1.2VDC 1800mA, 2x AAA 1.2VDC 900mA, 3x AAA 1.2VDC 500mA, 4x AAA 1.2VDC 500mA |
| Compatible Battery Types | Ni-MH, Ni-CD (AA/AAA) |
| Battery Capacity (AAA) | 1100mAh |
| Manufacturer | EBL |
7. What's in the Box
- 1 x EBL 907 LCD AA/AAA Rechargeable Battery Charger
- 8 x EBL 1100mAh AAA Rechargeable Batteries
8. Safety Information
Please read and follow these safety precautions to prevent injury or damage:
- Do not charge 1.5V alkaline or carbon batteries, as this may cause leakage or explosion.
- Do not disassemble or reassemble the charger for any reason.
- Use the charger only with compatible Ni-MH or Ni-CD rechargeable batteries.
- Keep the charger and batteries away from water, fire, and high temperatures.
- Do not short-circuit the battery terminals.
- Keep out of reach of children.
9. Warranty and Support
EBL products are designed for reliability and performance. This product is covered by the manufacturer's warranty. For specific warranty details, technical support, or customer service inquiries, please refer to the official EBL website or contact their customer support directly. Please retain your proof of purchase for warranty claims.
