Important Safety Information
- Use only cold tap water. Do not filter hot water.
- Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
- Keep the pitcher away from direct sunlight and heat sources.
- Wash all parts of the pitcher (except the filter) by hand with mild detergent. Do not use abrasive cleaners.
- The filter is not dishwasher safe.
Product Overview
The Brita Everyday Elite Water Filter Pitcher is designed to provide cleaner, great-tasting tap water by reducing various contaminants. It features a 10-cup capacity and a SmartLight filter indicator for convenient usage.
Image: The Brita Everyday Elite Water Filter Pitcher in black, shown with a blue Elite filter. The pitcher has a clear body and a black lid with a handle.
Image: A graphic illustrating the Brita Elite filter's capabilities, stating it reduces 5X contaminants including Chlorine, Lead, Microplastics, Select Pharmaceuticals & Pesticides, Mercury, and Cadmium.
Setup
- Wash Pitcher Components: Hand-wash the pitcher, lid, and reservoir with mild soap and water. Rinse thoroughly. Do not wash the filter with soap.
- Prepare the Filter: Remove the Brita Elite filter from its packaging. Rinse the filter under cold tap water for 15 seconds.
- Insert Filter: Insert the prepared filter into the reservoir by aligning the grooves and pressing down firmly until it clicks into place.
- Assemble Pitcher: Place the reservoir with the inserted filter into the pitcher. Secure the lid onto the pitcher.
- Initial Filter Flush: Fill the reservoir with cold tap water. Allow the water to filter through completely. Discard the first two pitchers of filtered water to flush out any carbon dust.
- Activate SmartLight Indicator: For Elite filters, press and hold the reset button on the lid for 6 seconds until the green light flashes. This indicates the filter life tracking has started.
Video: A demonstration of setting up the Brita Everyday Elite Water Filter Pitcher, including unpacking, inserting the filter, and filling with water. This video shows the ease of assembly and initial use.
Operating Instructions
- Filling the Pitcher: Open the easy-fill lid and place the pitcher under cold tap water. Fill the reservoir to the maximum fill line. The water will filter through to the main pitcher body.
- Pouring Water: Once the water has filtered, you can pour clean, filtered water from the pitcher.
- SmartLight Indicator: The SmartLight indicator on the lid will flash green, yellow, or red to indicate the filter's status. Green means good, yellow means it's time to order a new filter, and red means it's time to replace the filter.
Image: An illustration highlighting the key features of the Brita pitcher, such as the SmartFilter Alert on the lid, easy-fill lid, and the included Elite filter.
Maintenance
Filter Replacement
Replace the Brita Elite water filter approximately every 6 months or after filtering 120 gallons of water. The SmartLight indicator will signal when a replacement is needed.
- Remove Old Filter: Lift the reservoir out of the pitcher and remove the old filter by pulling it upwards.
- Prepare New Filter: Follow the preparation steps for a new filter as described in the Setup section (rinse under cold water for 15 seconds).
- Insert New Filter: Insert the new filter into the reservoir, ensuring a snug fit.
- Reset Indicator: After replacing the filter, press and hold the reset button on the lid for 6 seconds until the green light flashes to reset the filter life tracker.
Image: The Brita Everyday Elite Water Filter Pitcher, showing the filter visible within the reservoir. This image helps visualize where the filter is located for replacement.
Cleaning the Pitcher
- Hand-wash all pitcher components (except the filter) with mild detergent.
- Rinse thoroughly to remove all soap residue.
- Do not use abrasive cleaning agents or put any part of the pitcher in the dishwasher.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Slow Filtration | Filter is clogged or nearing end of life. | Replace the filter. Ensure the filter was properly rinsed before first use. |
| Water has an unusual taste/odor | Filter needs replacement or was not properly flushed. | Discard the first two pitchers of filtered water. If problem persists, replace the filter. |
| SmartLight indicator not working | Battery issue or not reset properly. | Ensure the indicator was reset by holding the button for 6 seconds. If still not working, contact Brita customer support. |
| Black flecks in water | Carbon dust from new filter. | This is normal for new filters. Discard the first two pitchers of filtered water. If flecks persist, re-rinse the filter. |
| Pitcher leaks | Lid or reservoir not properly seated. | Ensure the lid and reservoir are securely in place. Check for any cracks in the pitcher body. |
| Water not filtering | Filter not properly seated or clogged. | Remove and re-insert the filter, ensuring it is firmly seated. If still not filtering, replace the filter. |
| Water tastes like plastic | New pitcher plastic residue. | Wash all pitcher components thoroughly with mild soap and water before first use. Repeat if taste persists. |
| Water tastes like chlorine | Filter not effectively reducing chlorine. | Ensure filter is properly seated and reset. If taste persists, replace the filter. |
| Water tastes metallic | Filter not effectively reducing metals. | Ensure filter is properly seated and reset. If taste persists, replace the filter. |
| Water is cloudy | Air bubbles or sediment. | This is usually harmless air bubbles. Let the water sit for a few minutes. If sediment persists, replace the filter. |
| Pitcher is discolored | Staining from beverages or food. | Clean immediately after use. For stubborn stains, try a mixture of baking soda and water. |
| Filter indicator light not changing | Indicator malfunction. | Try resetting the indicator again. If it remains unresponsive, contact Brita customer support. |
| Water flow too fast | Filter not properly seated or defective. | Remove and re-insert the filter firmly. If flow remains too fast, replace the filter. |
| Water tastes like dirt/earthy | Filter is saturated or water source issue. | Replace the filter. If the taste persists, consider testing your tap water quality. |
Specifications
- Brand: Brita
- Model Name: Everyday Elite
- Model Number: OB46/OB06
- Capacity: 10 Cups (approx. 2.36 liters)
- Material: BPA-free Polystyrene
- Product Dimensions: 10.95"L x 10.83"W x 6.06"H
- Item Weight: 2.14 Pounds
- Special Feature: SmartLight Filter Change Indicator
- Filter Type: Brita Elite Filter (included)
- Filter Life: Approximately 6 months or 120 gallons
- Contaminant Reduction: Reduces 99% of Lead, Chlorine (taste and odor), Cadmium, Mercury, Benzene, Asbestos, and more.
- Installation Type: Freestanding
- Power Source: Manual Operation
- Supported Water TDS Level Maximum (PPM): 500
- Temperature Rating: 32-85 Degrees Fahrenheit
Warranty & Support
For warranty information or customer support, please refer to the official Brita website or contact their customer service directly. Keep your proof of purchase for any warranty claims.
Brita Elite filters are compatible with all Brita pitchers and dispensers except Stream models.
Note: Using non-Brita certified filters may void your warranty and may not provide the same level of contaminant reduction.
Image: A graphic emphasizing Brita's certifications, stating all products are certified by the Water Quality Association and filters meet NSF/ANSI standards 53, 42, and 401.
