Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Armacost Lighting RibbonFlex Pro 24-Volt Outdoor LED Tape Light. Please read all instructions thoroughly before beginning installation to ensure proper function and safety. This product is designed for outdoor accent lighting applications.
Image: Armacost Lighting RibbonFlex Pro LED Tape Light, 32.8 ft (10M) length, 3000K Soft White, 60 LEDs/meter, 24V, designed for wet locations.
Safety Information
- Always disconnect power before installation or servicing.
- This product is rated for IP67, meaning it is protected from dust and immersion in water between 5.9 – 39.37 inches (15cm – 1m) deep for up to 30 minutes. It is not intended for continuous submersion.
- Use only with a compatible 24-volt DC power supply (sold separately).
- Do not bend the tape light sharply or apply excessive force, as this may damage the LEDs or internal circuitry.
- Ensure all connections are secure and properly sealed, especially in outdoor environments, to maintain the IP67 rating.
- Installation should comply with all local electrical codes.
Package Contents
Verify that all components are present before beginning installation:
- RibbonFlex Pro 24-Volt White Outdoor Tape Light (32.8 ft / 10M)
- (1) Wire connector for bridging gaps or making turns
- (1) Splice connector to join tape light strips end-to-end
- (2) Heat shrink tubes for sealing connections
- (2) Peel-and-stick Wire Support Clips
- Detailed planning and installation guide (this manual)
- Low-voltage power wire leads: 8in and 48in
Note: A 24-volt power supply and optional dimmer/switch are sold separately.
Image: Contents of the RibbonFlex Pro package, highlighting the tape light, connectors, and accessories. A separate 24V power supply and optional dimmer are shown as required but not included.
Specifications
| Feature | Specification |
|---|---|
| Model Number | 145450 |
| Color Temperature | 3000K (Soft White) |
| Length | 32.8 ft (10 meters) |
| LEDs per Meter | 60 |
| Voltage | 24 Volts DC |
| Wattage | 22.5 watts (total) |
| Luminous Flux | 7900 Lumens (total) |
| Moisture Rating | IP67 (Water Resistant) |
| Adhesive | 3M Model 4229P VHB |
| Lifespan | 65,000+ hours |
| Dimmable | Yes (with optional dimmer) |
Image: Key specifications and features of the RibbonFlex Pro LED Tape Light, including lumens, IP rating, adhesive type, and lifespan.
Setup and Installation
Follow these steps for a successful installation:
1. Planning Your Layout
- Measure the area where the tape light will be installed.
- Identify the location for your 24V DC power supply (sold separately). Ensure it is protected from direct water exposure if not rated for outdoor use.
- Plan for any turns or gaps that may require the use of connectors.
Image: Various application examples for the LED tape light, including decks, patios, bathrooms, RVs, and boats.
2. Cutting and Connecting the Tape Light
- The tape light can be cut to custom lengths at designated cut marks (indicated by copper pads) every 4 inches. Use sharp scissors to ensure a clean cut.
- To connect multiple sections or bridge gaps, use the included splice or wire connectors. Ensure proper polarity (+ to + and - to -).
- For outdoor applications, use the heat shrink tubes to seal all connections, maintaining the IP67 rating. Apply heat evenly until the tube shrinks tightly around the connection.
Image: Instructions for customizing installation using splice and wire connectors to extend or route the tape light.
3. Mounting the Tape Light
- Clean the installation surface thoroughly. It must be dry, smooth, and free of dust, oil, and debris for optimal adhesion.
- Peel off the backing from the 3M VHB adhesive.
- Press the tape light firmly onto the desired surface. Apply pressure evenly along the entire length.
- Use the included wire support clips to secure any loose wires or sections of the tape light, especially around corners or where extra support is needed.
Image: Visual representation of the tape light's features, including its suitability for wet locations, dimmability, cut-to-size capability, peel-and-stick adhesive, and flexibility, demonstrated in an outdoor setting.
4. Connecting to Power Supply
- Connect the low-voltage power wire leads from the tape light to your 24V DC power supply (sold separately). Ensure correct polarity.
- If using an optional dimmer or switch, connect it between the power supply and the tape light according to the dimmer's instructions.
- Once all connections are secure, plug in the power supply to an appropriate electrical outlet.
Operating Instructions
The RibbonFlex Pro LED Tape Light operates on 24V DC power. Once properly installed and connected to a power supply, the lights will illuminate when power is applied.
- On/Off: Control power via the connected 24V DC power supply or an optional inline switch.
- Dimming: If an optional dimmer (e.g., an Armacost Lighting dimmer) is installed, use its controls to adjust the brightness from 0% to 100%.
- App Control: If using a compatible smart dimmer or controller, refer to its specific instructions for app-based control.
Maintenance
- Cleaning: Gently wipe the tape light with a soft, damp cloth. Avoid abrasive cleaners or solvents. Ensure the power is off before cleaning.
- Inspection: Periodically check connections and the adhesive backing for signs of wear or loosening, especially in outdoor environments. Re-secure or re-seal as needed.
- Environmental Protection: While IP67 rated, prolonged exposure to extreme weather conditions (e.g., heavy snow, standing water) may reduce lifespan. Ensure proper drainage around the installation area.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not turn on. | No power to the power supply; incorrect wiring; faulty power supply; damaged tape light. | Check power outlet and power supply connection. Verify all wiring connections for correct polarity. Test power supply. Inspect tape light for visible damage. |
| Lights flicker or are dim. | Insufficient power supply; loose connection; voltage drop over long runs; incompatible dimmer. | Ensure power supply wattage meets or exceeds total tape light wattage. Check all connections. Consider shorter runs or a larger gauge wire for extensions. Verify dimmer compatibility. |
| Sections of tape light are out. | Damaged section; poor connection at a splice/cut point. | Inspect the non-working section for physical damage. Re-check connections at cut points and splices. Replace damaged sections if necessary. |
| Adhesive is not holding. | Surface not clean or dry; surface material incompatible; insufficient pressure during installation. | Clean and dry surface thoroughly. Use additional mounting clips or a suitable outdoor adhesive for extra security. Ensure firm pressure was applied during initial installation. |
Warranty and Support
Armacost Lighting RibbonFlex Pro LED Tape Light comes with a 3-year limited warranty. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or further assistance, please contact Armacost Lighting customer service. Keep your proof of purchase for warranty validation.
Contact Information: Refer to the Armacost Lighting official website or your product packaging for the most current support details.
Online Resources: Visit the Armacost Lighting Store on Amazon for additional products and information.
