Important Safety Information
Please read and understand all instructions before beginning installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards that can cause property damage or personal injury.
- Always disconnect power at the main circuit breaker before installation, maintenance, or bulb replacement.
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure all electrical connections are secure and comply with local codes and ordinances.
- Do not install near flammable materials.
- Handle glass components with care to prevent breakage and injury.
Setup Instructions
Package Contents
Verify that all components are present before beginning installation. The package includes the lamp post assembly, three light fixtures with tempered ripple glass, a dusk-to-dawn sensor, and mounting hardware.
Figure 1: Product Components and Dimensions
Pre-installation
- This lamp post is designed for hard-wired electrical connections and is not solar-powered. Ensure a suitable 120V AC power source is available at the installation site.
- Prepare the ground masonry work in advance. The post base is designed to replace previous post bases with an existing bolt spacing of 7.68 inches apart.
- An additional template card is provided for quick positioning during installation.
Assembly and Installation
- Carefully unpack all components and inspect for any damage.
- Assemble the lamp post sections according to the provided diagrams, ensuring all connections are tight.
- Mount the assembled lamp post securely to the prepared ground masonry using the provided mounting hardware. Ensure the post is level and stable.
- Connect the electrical wiring from your power source to the lamp post's internal wiring. Follow all local electrical codes. This product is suitable for wet locations.
- Attach the three light fixtures to the top of the post.
- Install three E26 base bulbs (max 100W each, not included) into the sockets.
- Restore power at the circuit breaker and test the light functionality.
Figure 2: Installation Features
Operating Instructions
Dusk to Dawn Functionality
The VIANIS V82013 lamp post features a built-in high-sensitivity photocell sensor for automatic operation:
- The light will automatically turn OFF during the daytime when the ambient brightness exceeds 100 lux.
- The light will automatically turn ON at night when the ambient brightness falls below 20 lux.
This automatic feature provides convenience and energy efficiency, eliminating the need for manual operation.
Figure 3: Dusk to Dawn Sensor Operation
Bulb Replacement
The lamp post is designed for easy bulb replacement:
- The light fixtures have a bottom opening design.
- To replace a bulb, simply unscrew the old bulb and screw in a new E26 base bulb (max 100W). No tools are required for this process, which typically takes less than one minute per bulb.
Figure 4: Easy Bulb Replacement
Figure 5: Compatible E26 Bulb Types (Max 100W)
Maintenance
Cleaning
- To clean the lamp post and glass, ensure power is disconnected at the circuit breaker.
- Wipe surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish or glass.
- The tempered ripple glass is durable, but care should still be taken during cleaning.
Weather Resistance
The VIANIS V82013 is constructed from aluminum with a black finish, designed to be waterproof, anti-rust, and weather-resistant. It can withstand various outdoor conditions including rain, sun, snow, and wind.
Figure 6: Weather Resistance Features
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on at night. | 1. Power supply issue. 2. Faulty bulb. 3. Photocell sensor obstructed or malfunctioning. | 1. Check circuit breaker and wiring connections. 2. Replace bulb. 3. Ensure photocell is clear of debris and not exposed to other light sources at night. |
| Light does not turn off during the day. | 1. Photocell sensor not receiving enough light. 2. Photocell sensor malfunctioning. | 1. Ensure photocell is not obstructed or in a shaded area during the day. 2. Contact customer support if issue persists. |
| Light flickers. | 1. Loose wiring connection. 2. Faulty bulb. 3. Incompatible bulb type. | 1. Check all wiring connections (ensure power is off). 2. Replace bulb. 3. Ensure E26 bulbs are rated for 120V and compatible with outdoor use. |
Product Specifications
| Brand | VIANIS |
| Model Number | V82013 |
| Dimensions (L x W x H) | 22" x 22" x 78.7" (6.5 ft height) |
| Material | Aluminum, Tempered Ripple Glass |
| Color | Black |
| Power Source | Corded Electric |
| Voltage | 120 Volts (AC) |
| Bulb Base | E26 |
| Max Wattage per Bulb | 100 Watts |
| Number of Light Sources | 3 |
| Special Features | Dusk to Dawn Sensor, Anti-Rust, Water Resistant, Energy Efficient |
| Indoor/Outdoor Usage | Outdoor (Wet Location Rated) |
| Mounting Type | Floor Mount |
| Required Assembly | Yes |
Warranty Information
This VIANIS product is covered by a 1-year limited warranty from the date of purchase. This warranty covers manufacturing defects and material flaws under normal use. It does not cover damage caused by improper installation, accident, misuse, abuse, or acts of nature.
For warranty claims or service, please retain your proof of purchase.
Figure 7: Warranty and Certification
Customer Support
If you have any questions, require assistance with installation, or need to report a problem with your VIANIS Triple Head Dusk to Dawn Outdoor Post Light, please contact our customer support team.
Please refer to the contact information provided with your purchase or visit the official VIANIS website for support details.