Silverline 12 Cable Snake Harness Kit User Manual

Product Overview

The Silverline Audio 12 Cable Snake Harness Kit is designed as a comprehensive replacement or expansion solution for electronic drum kits. This kit provides all necessary cables to replace an existing cable snake or to add additional triggers to your current setup, ensuring reliable and clear signal transfer for your electronic drumming experience.

Each cable features nickel-plated plugs for rugged durability and efficient signal transfer, along with shielded, insulated, copper wiring for enhanced signal clarity, minimizing interference and ensuring accurate trigger response.

Image: The complete Silverline 12 Cable Snake Harness Kit, showing the bundled cables and individual plugs.

Package Contents

Your Silverline Audio 12 Cable Snake Harness Kit includes the following components:

• 12 Binded Cables: A complete set of cables pre-bundled for convenience.
  • 5x 10FT Dual Trigger Cables: Recommended for Ride, Crash 2, Crash 3, Tom 3, and Tom 4/Spare inputs.
  • 4x 6FT Dual Trigger Cables: Recommended for Tom 1, Tom 2, Crash 1, and Kick inputs.
  • 3x 4.5FT Dual Trigger Cables: Recommended for Hi-hat, Hi-Hat Control, and Snare inputs.
• 5 Additional Velcro Cable Wraps: For securing cables to your drum rack tubes or for general cable management.
• 1 Sticker Set: For labeling cables according to your specific setup and length preferences.

Image: Five black velcro cable wraps.

Image: Sheet of pre-printed stickers for labeling drum trigger cables (e.g., Snare, Tom, Crash, Ride, Kick, Hi-Hat).

Compatibility

This cable snake harness kit is compatible with a wide range of Yamaha electronic drum kits and modules that utilize 1/4 inch inputs/outputs. Specifically, it is designed for:

• Yamaha DTXPRESS
• Yamaha DTXPRESS II
• Yamaha DTXPRESS III

The kit is also compatible with the following Yamaha DTX modules:

• DTXPLORER, DTX502, DTXPRO, DTXPROX, DTXPRESS IV
• DTX, DTX Version 2, DTX500, DTX520K, DTX700
• DTXTREME, DTXTREME IIs, DTXTREME III, DTX900, DTX900M
• Yamaha RX5, TMX, and PTX8 modules (and others with 1/4 inch trigger inputs)

Note: While this kit provides 12 cables, some listed modules may have fewer than 12 trigger inputs. Conversely, a select few modules may have more than 12 inputs and could require additional single cables to utilize all available trigger inputs. Additional single cables can be purchased separately from Silverline Audio.

Setup and Installation

Follow these steps to properly install your Silverline Audio 12 Cable Snake Harness Kit:

1. Unpack the Kit: Carefully remove all components from the packaging.
2. Identify Cables: The cables are pre-bundled and color-coded at the plugs for easy identification. Refer to the recommended assignments for each cable length (e.g., 4.5ft for Snare, Hi-hat).


Image: Right-angle plugs with color-coded labels for various drum triggers (e.g., Kick, Hi-Hat, Crash).



Image: Straight plugs with color-coded labels for various drum triggers (e.g., Snare, Tom, Ride).

3. Connect to Drum Pads/Triggers: Connect the appropriate end of each cable to its corresponding drum pad or trigger. Ensure a firm and secure connection.
4. Connect to Drum Module: Route the other end of the cables to your electronic drum module. Connect each cable to the correct input on the module (e.g., "Snare" cable to "Snare" input).
5. Cable Management: Use the included velcro cable wraps to neatly bundle and secure the cables to your drum rack or other stable points. This helps prevent tangles and reduces strain on the connections.
6. Apply Labels (Optional): If desired, use the provided sticker set to apply custom labels to your cables, especially if you deviate from the recommended assignments or have a complex setup.

Operating Instructions

Once installed, the cable snake harness operates passively by transmitting trigger signals from your drum pads to your module. Ensure all connections are secure before use. When disconnecting, always grasp the plug itself, not the cable, to prevent damage to the wiring and connectors.

Maintenance and Care

• Keep Clean: Wipe cables periodically with a soft, dry cloth to remove dust and grime. Avoid using harsh chemicals or abrasive cleaners.
• Avoid Kinks and Sharp Bends: Do not bend cables at sharp angles, especially near the connectors, as this can damage the internal wiring.
• Proper Storage: When not in use, coil the cables loosely and secure them with the velcro wraps or other cable ties. Store them in a cool, dry place away from direct sunlight and extreme temperatures.
• Regular Inspection: Periodically inspect the cables and connectors for any signs of wear, fraying, or damage. Replace any damaged cables to ensure optimal performance and safety.

Troubleshooting

• No Signal or Intermittent Signal:
  • Ensure all cable connections at both the drum pad/trigger and the module are fully seated and secure.
  • Check if the correct cable is connected to the correct input on the module.
  • Test the problematic cable with a different input or a known working cable to isolate the issue.
• Incorrect Trigger Response:
  • Verify that the cable from a specific drum pad is connected to the corresponding input on the module (e.g., Snare pad to Snare input).
  • Check your drum module's settings to ensure proper trigger type and sensitivity are configured for each input.
• Physical Cable Damage:
  • Inspect the entire length of the cable and especially near the plugs for any visible cuts, kinks, or fraying. Damaged cables should be replaced.

Product Specifications

Warranty and Support

For any questions regarding the Silverline Audio 12 Cable Snake Harness Kit, including technical support or warranty inquiries, please contact Silverline Audio directly through their official channels. Refer to your purchase documentation or the Silverline Audio website for specific contact information and warranty terms.