TELEVES NanoKom Mast Amplifier and PicoKom Power Supply Kit User Manual

Introduction

This user manual provides essential information for the installation, operation, and maintenance of your TELEVES NanoKom Mast Amplifier (Ref. 561621) and PicoKom Power Supply (Ref. 5796) kit. This kit is designed to enhance television signal reception, ensuring optimal performance for your home entertainment system. Please read this manual thoroughly before installation and operation to ensure safe and correct usage.

Safety Information

• Always disconnect power before making any connections or disconnections.
• Ensure proper grounding to prevent electrical hazards.
• Do not expose the devices to moisture or extreme temperatures.
• Only use the provided PicoKom power supply with the NanoKom amplifier.
• Installation should be performed by qualified personnel if you are unsure about any steps.

Components Included

The TELEVES NanoKom Mast Amplifier and PicoKom Power Supply Kit typically includes:

• 1 x TELEVES NanoKom Mast Amplifier (Ref. 561621)
• 1 x TELEVES PicoKom Power Supply (Ref. 5796)
• Mounting accessories (screws, ties, etc.)
• Instruction manual (this document)

Setup and Installation

Follow these steps for proper installation of the mast amplifier and power supply.

1. NanoKom Mast Amplifier Installation (Ref. 561621)

The NanoKom amplifier is designed for outdoor mast mounting. Ensure it is placed in a location that provides optimal signal reception and protection from direct weather exposure, although it is designed for outdoor use.

1. Mount the amplifier securely to the mast using the provided mounting hardware.
2. Connect the antenna cables to the appropriate input ports on the amplifier. The amplifier features inputs for UHF, VHF, and SAT signals. Refer to the image below for port identification.
3. Connect the output cable from the amplifier's OUT port to the input of the PicoKom power supply.
4. Ensure all F-connectors are tightened securely to prevent signal loss and moisture ingress.

Figure 1: TELEVES NanoKom Mast Amplifier (left) and PicoKom Power Supply (right). The amplifier shows inputs for UHF, VHF, and SAT, along with an OUT port for connection to the power supply. It also features a DC UHF switch (OFF/ON) and indicates 12-24V power requirement. The power supply unit (Ref. 5796) has a Vdc input.

2. PicoKom Power Supply Connection (Ref. 5796)

The PicoKom power supply is designed for indoor use and provides the necessary power to the mast amplifier via the coaxial cable.

1. Connect the cable from the amplifier's OUT port to the input of the PicoKom power supply.
2. Connect the output of the PicoKom power supply to your television or distribution system.
3. Plug the PicoKom power supply into a standard electrical outlet.
4. Verify the DC UHF switch on the NanoKom amplifier is set correctly. If your UHF antenna requires DC power (e.g., for a pre-amplifier), set it to ON. Otherwise, set it to OFF.

Operating Instructions

Once installed and powered, the TELEVES NanoKom amplifier and PicoKom power supply operate automatically to amplify and distribute the television signal.

• Signal Amplification: The NanoKom amplifier boosts weak UHF, VHF, and SAT signals received by your antenna, improving picture quality and channel availability.
• Powering the Amplifier: The PicoKom power supply injects power (12-24Vdc) into the coaxial cable, which travels up to the mast amplifier.
• DC UHF Switch: This switch on the amplifier controls the DC power supply to the UHF input. Ensure it is set according to your antenna's requirements.

Maintenance

The TELEVES NanoKom and PicoKom units are designed for low maintenance. However, periodic checks can ensure long-term performance.

• Cleaning: Gently wipe the exterior of both units with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
• Cable Connections: Periodically check all coaxial cable connections for tightness and signs of corrosion. Re-tighten if necessary.
• Environmental Conditions: Ensure the outdoor amplifier is not obstructed by debris and that the indoor power supply is in a well-ventilated area, away from heat sources.

Troubleshooting

If you experience issues with signal reception, consider the following troubleshooting steps:

Specifications

Key technical specifications for the TELEVES NanoKom Mast Amplifier and PicoKom Power Supply Kit:

• Product Model: 438620
• NanoKom Mast Amplifier Reference: 561621
• PicoKom Power Supply Reference: 5796
• Input Frequencies: UHF, VHF, SAT
• Power Supply (PicoKom): 12-24Vdc (via coaxial cable)
• DC Pass (UHF): Selectable ON/OFF
• ASIN: B0B136T4QY

Warranty and Support

Warranty information for the TELEVES NanoKom Mast Amplifier and PicoKom Power Supply Kit is typically provided at the time of purchase or can be found on the official TELEVES website. For technical support, product registration, or warranty claims, please refer to the contact information provided with your purchase or visit the official TELEVES support portal.