Aerocool DELTABKV1 ATX PC Case User Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Aerocool DELTABKV1 ATX PC Case. Please read this manual thoroughly before beginning assembly to ensure proper setup and safe use of the product.

Image: Angled view of the Aerocool DELTABKV1 PC case, highlighting its RGB front panel design and the transparent tempered glass side panel.

1. Setup and Installation

Follow these steps for installing components into your Aerocool DELTABKV1 PC case.

1.1 Preparing the Case

1. Carefully unpack the PC case and remove all packaging materials.
2. Place the case on a stable, flat surface.
3. Remove the tempered glass side panel by unscrewing the thumb screws located at the rear of the panel. Gently slide the panel off and set it aside on a soft, non-abrasive surface to prevent scratches.
4. Remove the right-side metal panel by unscrewing its thumb screws to access the cable management area.

Image: Internal view of the PC case, illustrating the main compartment for motherboard and expansion cards, along with drive mounting points.

1.2 Motherboard Installation

1. Identify the correct standoff locations for your ATX, Micro-ATX, or Mini-ITX motherboard. The case may have pre-installed standoffs or marked positions.
2. Install any necessary additional standoffs.
3. Install the I/O shield into the rear opening of the case.
4. Carefully place the motherboard onto the standoffs, aligning the screw holes.
5. Secure the motherboard with the provided screws. Do not overtighten.

1.3 Storage Drive Installation

The case supports 2 x 3.5" HDDs and 2 x 2.5" SSDs.

• 3.5" HDDs: Locate the drive cage in the lower compartment. Slide the 3.5" drives into the bays and secure them with screws.
• 2.5" SSDs: Mount the 2.5" drives onto the designated mounting points behind the motherboard tray or in the drive cage, securing them with screws.

Image: View of the rear interior, illustrating the space for cable routing and mounting locations for 2.5-inch storage drives.

1.4 Power Supply Unit (PSU) Installation

1. Position the PSU in the dedicated compartment at the bottom rear of the case.
2. Ensure the PSU fan faces downwards (if there's a filtered vent at the bottom) or upwards, depending on your cooling preference and PSU design.
3. Secure the PSU to the case with screws from the rear.

1.5 Expansion Card (GPU) Installation

1. Remove the necessary PCI slot covers from the rear of the case.
2. Insert your graphics card or other expansion cards into the appropriate PCIe slots on the motherboard.
3. Secure the expansion card(s) with screws. The case supports graphics cards up to 307mm in length.

Image: Rear exterior of the case, displaying the PCI expansion slots, the cutout for the power supply, and the pre-installed 12cm rear fan.

1.6 Fan and Cooling Installation

The case includes one 12cm rear fan. Additional fan configurations are supported:

• Front: 3 x 12cm fans (optional)
• Top: 2 x 12cm fans (optional)
• Rear: 1 x 12cm fan (pre-installed)
• PSU Shroud: 2 x 12cm fans (optional)

For liquid cooling, a 12cm radiator can be installed at the rear.

1.7 Front Panel Connections

Connect the front panel cables (USB, HD Audio, Power, Reset, LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for specific header locations.

Image: Top-front perspective of the case, highlighting the accessible front I/O panel which includes USB ports, audio jacks, and control buttons.

1.8 Cable Management

Utilize the space behind the motherboard tray and the cable tie-down points to route and secure cables. This improves airflow and aesthetics.

1.9 Final Assembly

1. Once all components are installed and cables are managed, reattach the right-side metal panel.
2. Carefully reattach the tempered glass side panel and secure it with the thumb screws.

2. Operating the Case Features

2.1 RGB Lighting Control

The Aerocool DELTABKV1 features an RGB front panel with integrated lighting modes. Use the dedicated LED control button on the top panel to cycle through various lighting effects and colors. Press and hold the LED button for a few seconds to turn the RGB lighting on or off.

Image: Direct front view of the PC case, emphasizing the distinctive RGB lighting design on the front panel.

2.2 Front Panel Ports

The top panel provides convenient access to:

• USB 2.0 Ports (x2)
• HD Audio Jacks (Headphone and Microphone)
• Power Button
• Reset Button
• LED Control Button

Ensure these are correctly connected to your motherboard for full functionality.

3. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your PC case.

• Dust Filters: Periodically check and clean any removable dust filters (e.g., under the PSU, front intake). Use compressed air or a soft brush to remove accumulated dust.
• Exterior Cleaning: Wipe the exterior surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents. For the tempered glass panel, use a glass cleaner and a microfiber cloth.
• Internal Dust: Every few months, open the case and use compressed air to gently remove dust from internal components and fan blades. Ensure the system is powered off and unplugged before cleaning.

4. Troubleshooting

This section addresses common issues you might encounter.

• No Power:
  • Ensure the PSU is switched on and properly connected to the wall outlet.
  • Verify that the power button cable from the case is correctly connected to the motherboard's front panel header.
  • Check all internal power connections (24-pin ATX, 8-pin CPU, GPU power).
• Fans Not Spinning:
  • Confirm fan cables are securely connected to the motherboard fan headers or a fan controller.
  • Check BIOS/UEFI settings for fan speed control.
• RGB Lighting Not Working:
  • Ensure the RGB cable from the front panel is connected to the appropriate RGB header on your motherboard or a dedicated RGB controller.
  • Press the LED control button on the top panel to cycle through modes.
  • Check for any software control if connected to a motherboard RGB header.
• Front Panel USB/Audio Not Working:
  • Verify that the USB and HD Audio cables from the case are correctly connected to the corresponding headers on your motherboard.

If issues persist, consult your motherboard manual or the component manufacturer's support resources.

5. Specifications

6. Warranty and Support

The Aerocool DELTABKV1 PC Case is covered by the manufacturer's standard warranty. For specific warranty terms, duration, and support inquiries, please refer to the official AeroCool website or contact their customer service directly. Keep your proof of purchase for warranty claims.

For further assistance, visit the AeroCool official website.