Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your Yitong Angel Full Size Bed Frame (14 Inch). Please read all instructions carefully before assembly and use to ensure safe and proper functioning of the product.
Image: The Yitong Angel Full Size Bed Frame, fully assembled and ready for a mattress.
Safety Information
Important Safety Warnings:
- Do not exceed the maximum weight capacity of 3500 lbs. Overloading may cause structural damage and injury.
- Exercise caution during assembly and handling to avoid injury from sharp edges or pinch points.
- Ensure all bolts and connections are securely tightened before use and periodically check for tightness.
- Keep small parts away from children during assembly to prevent choking hazards.
- Do not jump on the bed frame.
- Use on a flat, level surface to prevent instability.
Components List
Before beginning assembly, verify that all parts are present and undamaged. Refer to the included assembly diagram for specific part identification.
- Metal Frame Sections (Side Rails, Center Support, Crossbars)
- Steel Slats
- Fasteners (Bolts, Washers)
- Assembly Tool (Hex Key)
- Non-slip Mattress Gaskets (4 pieces)
- Rubber Foot Plugs
Image: Close-up of key components: strong structure, anti-slip gaskets, and rubber foot plugs.
Setup Instructions
Assembly typically takes approximately 15-30 minutes. It is recommended to have two people for easier assembly.
Step-by-Step Assembly:
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
- Assemble Frame Sections: Connect the main frame sections using the provided bolts and washers. Ensure all connections are aligned correctly before tightening.
- Install Center Support: Attach the center support bar(s) to the main frame.
- Place Steel Slats: Position the steel slats across the frame. The U-shaped grooves are designed to prevent slats from slipping.
- Secure Slats: The steel slats come with four strips of tape to help reduce mattress slippage. Ensure these are properly adhered.
- Attach Foot Plugs: Insert the rubber foot plugs into the bottom of the bed frame legs. These prevent sliding and protect your floor.
- Final Tightening: Once all parts are in place, securely tighten all bolts using the provided hex key. Do not overtighten.
- Install Mattress Stoppers: Attach the non-slip mattress gaskets (stoppers) to the designated slots on the frame to prevent mattress movement.
Assembly Video Guide:
Video: Official Yitong Angel assembly guide for MT05-14 bed frames. This video demonstrates the step-by-step process of connecting the frame components and securing them.
Video: Official Yitong Angel guide on the correct installation of mattress stoppers. This video shows how to properly attach the non-slip gaskets to prevent mattress movement.
Key Features for Stability and Convenience:
Image: Dimensions (74.5"L x 53.5"W x 14"H) and maximum load capacity of 3500 lbs.
Image: Illustration of the 12-inch under-bed clearance for storage.
Image: Detail of the U-shaped groove for slat stability and the horizontal add-on tube for improved load bearing.
Operating Guidelines
The Yitong Angel Full Size Bed Frame is designed for use with a full-size mattress (75" x 54"). No box spring is required due to the robust steel slat support system.
- Place your mattress directly onto the steel slats.
- Ensure the mattress is centered on the frame and rests securely against the non-slip gaskets.
- Utilize the 12-inch under-bed clearance for convenient storage of items.
Maintenance
- Regular Inspection: Periodically (e.g., every 3-6 months) inspect all bolts and connections to ensure they remain tight. Retighten as necessary to maintain stability and prevent squeaking.
- Cleaning: Wipe the metal frame with a damp cloth and mild detergent. Avoid abrasive cleaners or solvents that could damage the finish.
- Floor Protection: The rubber foot plugs are designed to protect your floors. Check them occasionally for wear and tear.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Squeaking Noise | Loose bolts or connections. | Check and tighten all bolts securely. Ensure all frame parts are properly seated. |
| Mattress Slippage | Non-slip tape on slats is worn or mattress stoppers are not installed/positioned correctly. | Ensure mattress stoppers are firmly in place. If tape is worn, consider adding additional non-slip material between the mattress and slats. |
| Frame Instability | Uneven assembly or placement on an uneven floor. | Verify all connections are tight and the frame is assembled correctly. Move the frame to a level surface. |
| Missing Parts | Packaging error. | Contact customer support with your purchase details for assistance. |
Specifications
- Model Number: MT05-JD-14F
- Size: Full
- Product Dimensions (L x W x H): 74.5" x 53.5" x 14"
- Material: Alloy Steel
- Color: Black
- Maximum Weight Recommendation: 3500 lbs
- Under-bed Clearance: 12 inches
- Assembly Time: Approximately 15-30 minutes
- Box Spring Required: No
- Special Features: Easy Assembly, Heavy Duty Metal, Steel Slat Support, No Box Spring Needed, Squeak Resistant, Non-slip Design
Warranty & Support
For warranty information or customer support, please refer to the documentation included with your purchase or contact Yitong Angel customer service directly. Keep your proof of purchase for any warranty claims.
Return Policy: This product typically includes a 30-day return/replacement policy from the date of purchase. Please check with your retailer for specific return procedures.