steelmate 986X Motorcycle 2-Way Security Alarm System with Engine Starter

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your steelmate 986X Motorcycle 2-Way Security Alarm System. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.

Key Features

• 2-Way Communication: Remote monitoring with a transmission range of approximately 150m and a reception range of approximately 1000m. Notifies the remote control of any motorcycle abnormalities.
• Security Alarm Function: Warns with a siren (120dB) and flashing turn signals. Features a two-stage warning system: a light warning for initial shock detection, followed by full alarm activation (engine lock, 15-second siren, flashing turn signals) if shock is detected again within 15 seconds. Remote control is also notified.
• Remote Engine Starter: Allows remote starting of the engine, ideal for warming up the motorcycle.
• Keyless Operation: Enables starting the engine without a physical key.
• Anti-Hijack Function: Forcibly stops the engine. Pressing the stop button activates an alarm after 10 seconds, followed by engine shutdown.
• High-Sensitivity Shock Sensor: Built-in sensor with 3-level sensitivity adjustment via the remote control.
• Time Display & Alarm Setting: Functions displayed on the remote control.
• Parking Location Confirmation: Convenient for locating your vehicle in a parking lot.
• Battery Voltage Monitoring: Helps in managing the motorcycle's battery.
• Reception Signal Strength Display: Allows checking of the receivable area on the remote control.
• Compact Remote Controls: Includes two ultra-compact remote controls with built-in rechargeable lithium batteries.
• Security LED: Included for visual deterrence.

Package Contents

The steelmate 986X system includes the following components:

• 1 x Control Box (daily waterproof specification)
• 1 x Alarm Unit (Siren)
• 2 x Remote Controls (with built-in rechargeable lithium batteries)
• 1 x USB Charging Cable
• 1 x Wiring Harness Set
• 1 x Instruction Manual (Japanese version)

Image: The steelmate 986X package contents, showing the control box, alarm unit, two remote controls, wiring harness, USB charging cable, and the instruction manual.

Image: All individual components of the steelmate 986X alarm system laid out on a flat surface, including the main control unit, siren, two remote controls, wiring, and charging cable.

Setup and Installation

ATTENTION: This product can only be used for a 9-18V motorcycle. It is highly recommended to have this product installed by a professional technician. The operating range of this system may be affected by weather conditions, nearby radio/cellular structures, or other motorcycles.

Installation involves connecting the control box and alarm unit to your motorcycle's electrical system. Refer to the wiring diagrams below for specific connections based on your motorcycle's power generation type (AC or DC).

Wiring Diagram (AC Generation)

Image: Detailed wiring diagram for the steelmate 986X alarm system, specifically for motorcycles with AC power generation. It shows connections for the AC ECU, LED, siren, battery, engine lock, ignition code, turn signals, and engine start.

Wiring Diagram (DC Generation)

Image: Detailed wiring diagram for the steelmate 986X alarm system, specifically for motorcycles with DC power generation. It illustrates connections for the DC ECU, LED, siren, battery, engine lock, ignition code, turn signals, and engine start, including a normal close relay.

General Installation Steps (Consult a professional)

1. Mount the Control Box: Secure the main control box in a hidden, dry location on the motorcycle. Ensure it is protected from direct water exposure.
2. Connect Power: Connect the main power wires (red for positive, black for negative) to the motorcycle's 12V battery.
3. Connect Siren: Mount the alarm unit (siren) in a secure location and connect its wires to the control box.
4. Integrate with Ignition: Connect the engine lock and engine starter wires according to the appropriate wiring diagram (AC or DC) to your motorcycle's ignition system. This typically involves cutting and splicing ignition wires.
5. Connect Turn Signals: Connect the turn signal wires to your motorcycle's left and right turn signal circuits.
6. Install Security LED: Mount the security LED in a visible location and connect it to the control box.
7. Test Functionality: After all connections are made, test all alarm functions, remote start, and keyless operation to ensure correct installation.

Operating Instructions

Arming the Alarm

• Press the Lock button on the remote control once. The system will emit a confirmation sound, and the turn signals will flash once. The security LED will begin to flash.
• The shock sensor is now active. If a light shock is detected, a warning sound will occur. If a stronger shock is detected within 15 seconds, the full alarm will activate.

Disarming the Alarm

• Press the Unlock button on the remote control once. The system will emit two confirmation sounds, and the turn signals will flash twice. The security LED will turn off.

Remote Engine Start

• Ensure the motorcycle is in neutral.
• Press the Engine Start button (often a lightning bolt or star icon) on the remote control twice within 3 seconds. The engine should start.
• To stop the engine remotely, press the Unlock button or the Engine Stop button.

Anti-Hijack Function

• In an emergency, press and hold the Stop button on the remote control.
• After 10 seconds, the alarm will sound, and the engine will forcibly shut down.

Adjusting Shock Sensor Sensitivity

• Refer to the remote control's display and specific button combinations (usually found in the detailed Japanese manual) to cycle through the three sensitivity levels.

Parking Location Confirmation

• Press the Locate button (often a bell or horn icon) on the remote control. The motorcycle will emit a sound and flash its turn signals, helping you find it.

Maintenance

• Remote Control Battery: The remote controls have built-in rechargeable lithium batteries. Recharge them using the provided USB charging cable when the battery indicator on the remote control shows low power.
• System Check: Periodically check all wiring connections to ensure they are secure and free from corrosion.
• Cleaning: Keep the control box and alarm unit clean and free from excessive dirt or moisture. The control box has a daily waterproof specification, but avoid direct high-pressure water jets.
• Software Updates: No user-performable software updates are typically available for this type of device.

Troubleshooting

If you encounter problems not listed here or if the suggested solutions do not resolve the issue, please contact customer support.

Specifications

• Model Number: 986X
• Purpose: Anti-theft, Engine Starter Function
• Weight (Main Unit & Parts): 0.7 kg
• Remote Control Weight (per unit): 30 g
• Control Box Dimensions (L*W*H): 7.5 x 6.5 x 2 cm
• Remote Control Dimensions (L*W*H): 7 x 3.5 x 1 cm
• Operating Voltage: 12V ± 2V
• Standby Current: < 20mA
• Siren Output: 120dB
• Remote Control Included: Yes (2 units)
• Manufacturer: steelmate Co., Ltd.

Warranty Information

This product comes with a 1-year warranty from the date of purchase. During this period, steelmate Co., Ltd. will provide free repair or replacement for any malfunctions. This warranty does not cover malfunctions or damage caused by human error, natural disasters, or other external factors.

Support

For technical assistance, warranty claims, or any questions regarding your steelmate 986X Motorcycle Security Alarm System, please contact your retailer or the official steelmate customer support channel. Please have your product model number (986X) and purchase date available when contacting support.