1. Introduction
The Fenix LD22 v2.0 is a versatile and compact AA flashlight designed for everyday carry (EDC) and various outdoor activities. It features a maximum output of 800 lumens and offers dual power source compatibility, allowing use with either the included USB-C rechargeable battery or two standard AA batteries. This manual provides detailed instructions for the proper use, maintenance, and care of your Fenix LD22 v2.0 flashlight.
Overview of the Fenix LD22 v2.0 flashlight, highlighting its 800 lumen maximum output.
2. Package Contents
Upon opening the package, verify that all items listed below are present:
- Fenix LD22 v2.0 Flashlight
- Fenix ARB-L14-1100U Rechargeable Battery (1100mAh, USB-C)
- Pairdeer AA Alkaline Batteries (2x)
- USB-C Charging Cable
- Holster
- Lanyard
- LumenTac Battery Organizer
The Fenix LD22 v2.0 flashlight shown with its complete set of accessories, including batteries, charging cable, holster, and battery organizer.
3. Setup
3.1 Battery Installation
- Unscrew the tail cap of the flashlight counter-clockwise.
- Insert the Fenix ARB-L14-1100U rechargeable battery with the anode (+) end facing towards the flashlight head. Alternatively, insert two AA alkaline batteries with the anode (+) ends facing towards the flashlight head.
- Screw the tail cap back on clockwise until it is securely tightened.
3.2 Charging the ARB-L14-1100U Battery
The included Fenix ARB-L14-1100U battery features a built-in USB-C charging port.
- Locate the USB-C port on the side of the ARB-L14-1100U battery.
- Connect the provided USB-C charging cable to the battery and a compatible USB power source (e.g., computer, wall adapter).
- The indicator light on the battery will show charging status. Refer to the battery's specific instructions for full details on charging indicators.
- Once charging is complete, disconnect the cable.
The Fenix ARB-L14-1100U rechargeable battery connected to a USB-C charging cable, demonstrating the charging process. Also shown are two AA batteries and the flashlight.
4. Operating Instructions
The Fenix LD22 v2.0 features a dual switch system for intuitive control.
4.1 Power On/Off
- To turn on: Fully press the tail switch.
- To turn off: Fully press the tail switch again.
- Momentary on: Lightly press and hold the tail switch. Release to turn off.
4.2 Mode Switching (General Mode)
With the light on, single click the side switch to cycle through the brightness levels in the following order: Eco → Low → Med → High → Turbo.
4.3 Special Modes (Strobe & SOS)
With the light on, press and hold the side switch for 0.8 seconds to activate Strobe mode. In Strobe mode, single click the side switch to cycle between Strobe and SOS modes.
Illustration of the dual switch system, detailing the functions of the tactical tail switch and the functional side switch for mode selection.
A user demonstrating the Fenix LD22 v2.0 flashlight in a dark environment, highlighting its illumination capability.
5. Maintenance
5.1 Cleaning
Regularly clean the flashlight's threads and O-rings with a clean cloth. Apply a thin layer of silicone-based lubricant to the O-rings periodically to maintain water resistance.
5.2 Battery Care
- Remove batteries from the flashlight if it will not be used for an extended period to prevent leakage.
- For alkaline batteries, check periodically for signs of leakage and replace as needed.
- Store batteries in a cool, dry place.
6. Troubleshooting
If your flashlight is not functioning correctly, consider the following:
- Light does not turn on: Ensure batteries are inserted correctly with the correct polarity. Check if the tail cap is fully tightened.
- Light flickers or turns off intermittently: Clean the battery contacts and threads. Ensure batteries are fully charged or replaced.
- Reduced brightness or runtime: Batteries may be low on charge or nearing the end of their lifespan. Replace or recharge batteries.
- Water ingress: Check O-rings for damage or proper seating. Ensure all parts are securely tightened.
If issues persist, contact Fenix customer support for further assistance.
7. Specifications
The following table outlines the technical parameters of the Fenix LD22 v2.0 flashlight:
Detailed technical specifications including output, runtime, distance, and intensity for different modes and battery types.
| Feature | Value |
|---|---|
| Special Feature | Impact Resistant, Rechargeable |
| Color | Black |
| Power Source | Battery Powered |
| Light Source Type | LED |
| Material | Aluminum |
| White Brightness | 800 Lumens (Max) |
| Product Dimensions | 5.83"D x 0.85"W x 0.71"H |
| Item Weight | 3.39 Ounces |
| Water Resistance Level | Waterproof (IP68) |
| Battery Cell Composition | Lithium Ion (for rechargeable) |
| Finish Type | HA III Hard Anodized |
8. Warranty and Support
The Fenix LD22 v2.0 flashlight comes with a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your product or visit the official Fenix website.
For product support, technical assistance, or warranty claims, please contact Fenix customer service or visit the official Fenix store online:
