1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the RHOX Red Hawk LIFT-310 Lift Kit. This kit is designed to provide a 3-inch lift for E-Z-Go TXT Gas golf carts manufactured between 2008.5 and 2019, specifically those equipped with a Kawasaki engine. Please read this manual thoroughly before beginning installation to ensure proper fitment and safe operation.
2. Safety Information
WARNING: Improper installation or use of this lift kit can result in serious injury or death. Always follow all instructions and safety precautions.
- Ensure the golf cart is on a level surface and properly secured with wheel chocks before beginning any work.
- Disconnect the battery before performing any electrical work.
- Wear appropriate personal protective equipment, including safety glasses and gloves.
- Do not exceed the manufacturer's recommended weight capacity for the golf cart after lift kit installation.
- Always use proper lifting equipment, such as a hydraulic jack and jack stands, to support the golf cart.
- After installation, verify all fasteners are tightened to the manufacturer's specifications.
- Perform a test drive in a safe, open area to ensure proper function and handling before regular use.
3. Package Contents
Carefully unpack all components and verify that all items listed below are present and undamaged. If any parts are missing or damaged, contact customer support immediately.
Image: All components of the Red Hawk LIFT-310 Lift Kit, including drop spindles, mounting plates, U-bolts, nuts, and washers.
- Drop Spindles (2)
- Mounting Plates (2)
- U-Bolts (4)
- Nuts and Washers (as required for U-bolts)
- Installation Hardware (various bolts, nuts, washers)
4. Setup and Installation
This section outlines the general steps for installing the LIFT-310 Lift Kit. Professional installation is recommended. Refer to your golf cart's service manual for specific torque specifications and additional disassembly/assembly procedures.
4.1 Pre-Installation Steps
- Park the golf cart on a firm, level surface.
- Engage the parking brake.
- Place wheel chocks behind the rear wheels.
- Loosen the lug nuts on the front wheels.
- Using a hydraulic jack, lift the front of the golf cart until the front wheels are off the ground.
- Place jack stands securely under the frame of the golf cart, ensuring stability.
- Remove the front wheels.
4.2 Front Lift Kit Installation
- Remove Existing Components: Carefully remove the existing front suspension components, including the original spindles, shock absorbers, and any associated hardware. Keep track of all removed parts for potential reinstallation or reference.
- Install Drop Spindles: Attach the new drop spindles to the existing steering and suspension points. Ensure proper orientation as per the kit's specific design.
- Install Mounting Plates: Secure the provided mounting plates to the appropriate locations on the axle and/or frame, as instructed by the kit's design. These plates typically provide the necessary offset for the lift.
- Secure with U-Bolts: Use the provided U-bolts, nuts, and washers to firmly secure the new components. Tighten all fasteners evenly and to the manufacturer's recommended torque specifications.
- Reinstall Shocks and Steering: Reattach the shock absorbers and steering linkage to the new drop spindles. Ensure all connections are secure and free of binding.
- Repeat for Other Side: Perform the same steps for the opposite side of the golf cart.
4.3 Post-Installation Checks
- Reinstall the front wheels and tighten lug nuts to specification.
- Remove jack stands and carefully lower the golf cart to the ground.
- Bounce the front of the golf cart several times to allow the suspension to settle.
- Re-check all nuts and bolts for proper tightness.
- Perform a front-end alignment. Lifting a golf cart significantly alters suspension geometry, requiring alignment to prevent premature tire wear and ensure proper handling.
Image: A white golf cart with a lift kit installed, showcasing the increased ground clearance and larger tires.
5. Operating Considerations After Lift Kit Installation
After installing the LIFT-310 Lift Kit, the handling characteristics of your golf cart will change. Be aware of the following:
- Increased Center of Gravity: The golf cart's center of gravity will be higher, which can affect stability, especially during turns or on uneven terrain. Exercise caution and reduce speed in these situations.
- Tire Clearance: Ensure adequate clearance between the tires and all suspension/body components, especially during full steering lock and suspension travel.
- Braking Performance: Monitor braking performance. If larger tires were installed, braking distances may increase.
- Steering Response: The steering response may feel different. Allow time to adjust to the new handling characteristics.
Image: A yellow golf cart with a lift kit and an aftermarket light bar, demonstrating the enhanced appearance and utility.
6. Maintenance
Regular inspection and maintenance are crucial for the longevity and safe operation of your lifted golf cart.
- Periodic Inspection: Regularly inspect all components of the lift kit for signs of wear, damage, or corrosion. Check for loose bolts, cracked welds, or bent parts.
- Fastener Torque: Re-check the torque on all nuts and bolts associated with the lift kit and suspension components after the first 50 hours of operation, and then every 100 hours or annually, whichever comes first.
- Lubrication: Lubricate any grease fittings on the suspension components as recommended by the golf cart manufacturer.
- Alignment: Have the front-end alignment checked periodically, especially if you notice uneven tire wear or changes in steering.
- Cleaning: Keep the suspension components clean to prevent dirt and debris buildup, which can accelerate wear.
7. Troubleshooting
This section addresses common issues that may arise after installing a lift kit.
| Symptom | Possible Cause | Solution |
|---|---|---|
| Uneven ride height | Improper installation; uneven spring compression; damaged component | Verify all components are installed correctly and tightened evenly. Inspect springs and shocks for damage. |
| Excessive tire wear | Incorrect wheel alignment; unbalanced tires; worn suspension components | Perform a professional wheel alignment. Check tire balance. Inspect and replace worn suspension parts. |
| Steering looseness or difficulty | Loose steering components; worn tie rod ends; improper alignment | Inspect all steering linkages for tightness. Replace worn tie rod ends. Perform a wheel alignment. |
| Noise from suspension | Loose fasteners; worn bushings; component rubbing | Check all bolts and nuts for tightness. Inspect bushings for wear and replace if necessary. Identify and address any rubbing components. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | LIFT-310 |
| Brand | RHOX (Red Hawk) |
| Compatible With | E-Z-GO TXT Gas (2008.5-2019) with Kawasaki Engine |
| Lift Height | 3 Inches (Drop Spindle) |
| Auto Part Position | Front |
| Material | Alloy Steel |
| Included Components | Installation Hardware |
| Item Weight | 19.9 pounds |
| Product Dimensions | 25.9 x 13.4 x 7 inches |
| UPC | 814192029745 |
9. Warranty and Returns
This product is covered by a 30-day return policy and a 1-year warranty.
- 30-Day Return Policy: If the product does not meet your expectations upon arrival, you may return it within 30 days for a refund. The item must be in its original packaging and in good, undamaged condition.
- 1-Year Warranty: Beyond the 30-day return period, the product is eligible for replacement within one year of the order date if it experiences defects or issues covered under warranty.
For warranty claims or returns, please contact the seller or manufacturer directly with your purchase details.
10. Customer Support
For technical assistance, questions regarding installation, or warranty inquiries, please refer to the contact information provided by your retailer or the manufacturer, RHOX/Red Hawk.
It is recommended to have your product model number (LIFT-310) and purchase date available when contacting support.
