Introduction
Welcome to your KREAFUNK aHEAD 2 Wireless Bluetooth On-Ear Headphones. This manual provides essential information for setup, operation, and maintenance to ensure optimal performance and longevity of your device. Please read these instructions carefully before use.
Package Contents
- KREAFUNK aHEAD 2 Wireless Bluetooth On-Ear Headphones
- Charging Cable
- Washable Sports Cushions
Setup
Charging the Headphones
Before first use, fully charge your aHEAD 2 headphones.
- Connect the charging cable to the headphone's charging port.
- Connect the other end of the cable to a USB power source.
- The charging indicator light will illuminate.
- A full charge takes approximately 1.5 hours.
- Once fully charged, the indicator light will change or turn off.
Pairing with a Bluetooth Device
- Ensure the headphones are powered off.
- Press and hold the power button until the indicator light flashes, indicating pairing mode.
- On your device (smartphone, tablet, laptop), enable Bluetooth and search for available devices.
- Select "KREAFUNK aHEAD 2" from the list.
- Once paired, the indicator light will stop flashing and remain solid, or turn off.
- The headphones will automatically connect to the last paired device when powered on, if Bluetooth is enabled on the device.
Image: KREAFUNK aHEAD 2 headphones, showing the right earcup with control buttons for setup and operation.
Operating Instructions
Power On/Off
To power on, press and hold the power button until the indicator light illuminates. To power off, press and hold the power button until the indicator light turns off.
Volume Control
Use the '+' button to increase volume and the '-' button to decrease volume.
Music Playback
- Press the multi-function button (KREAFUNK logo button) once to play or pause music.
- Double-press the multi-function button to skip to the next track.
- Triple-press the multi-function button to go to the previous track.
Call Management
- To answer an incoming call, press the multi-function button once.
- To end a call, press the multi-function button once.
- To reject an incoming call, press and hold the multi-function button for 2 seconds.
Active Noise Cancellation (ANC)
The aHEAD 2 headphones feature Active Noise Cancellation. This function is controlled by a sensitive touch sensor.
To activate or deactivate ANC, gently press the designated sensor area on the earcup. A voice prompt will confirm the change in status.
Note: Due to the sensitivity of the sensor, accidental activation or deactivation may occur from hair contact or wind.
Image: Close-up view of the KREAFUNK aHEAD 2 headphone's right earcup, highlighting the control buttons for volume and playback, and the KREAFUNK logo multi-function button.
Maintenance
Cleaning
Wipe the headphones with a soft, dry cloth. Do not use abrasive cleaners or solvents.
The sports cushions are washable. Remove them carefully and wash according to fabric care instructions. Ensure they are completely dry before reattaching.
Storage
Store the headphones in a cool, dry place away from direct sunlight and extreme temperatures.
Water Resistance
The headphones are IPX4 water resistant, meaning they are protected against splashing water from any direction. They are not designed for submersion in water. Avoid exposing them to heavy rain or direct water jets.
Image: KREAFUNK aHEAD 2 headphones in purple, showing water droplets on the earcup, illustrating their IPX4 water resistance.
Troubleshooting
No Power
- Ensure the headphones are fully charged.
- Check the charging cable and power source.
Cannot Pair
- Ensure Bluetooth is enabled on your device.
- Make sure the headphones are in pairing mode (flashing indicator light).
- Move the headphones closer to your device.
- Forget "KREAFUNK aHEAD 2" from your device's Bluetooth list and attempt to pair again.
Poor Sound Quality
- Check the volume level on both the headphones and your connected device.
- Ensure there are no obstructions between the headphones and your device.
- Try pairing with a different device to rule out device-specific issues.
ANC Issues
- Ensure the ANC sensor area is clean and free from obstructions.
- Avoid touching the sensor area accidentally.
Specifications
| Feature | Detail |
|---|---|
| Model Name | aHEAD 2 |
| Model Number | KFLK22 |
| Connectivity Technology | Bluetooth, Wireless |
| Bluetooth Version | 5.0 |
| Bluetooth Range | 10 Meters |
| Noise Control | Active Noise Cancellation |
| Charging Time | 1.5 Hours |
| Playtime | Up to 20 hours |
| Water Resistance Level | IPX4 Water Resistant |
| Frequency Range | 20 Hz - 20,000 Hz |
| Built-in Microphone | Yes |
| Control Method | Touch (for ANC), Media Control (buttons) |
| Product Dimensions | 6.3 x 1.97 x 6.69 inches |
| Item Weight | 1.1 pounds (0.5 Kilograms) |
| Manufacturer | KREAFUNK |
Warranty and Support
KREAFUNK products are designed with quality and durability in mind. For warranty information and support, please refer to the official KREAFUNK website or contact their customer service directly. Keep your proof of purchase for warranty claims.
Official KREAFUNK Website: www.kreafunk.com
