Sharper Image Calming Heat Sauna Wrap Instruction Manual

Introduction

Welcome to your new Sharper Image Calming Heat Sauna Wrap. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your device. Please read all instructions carefully before first use.

Important Safety Information

WARNING: To reduce risks of injury, read all instructions before first use.

• Only use on flat surfaces and never heat when folded.
• Wear comfortable, full-length, skin-covering clothing.
• Breathable socks with a higher cotton content perform best.
• Socks are required and must be worn.
• AVOID wearing tight-fitting Lycra or workout-based clothing.
• You must have a barrier between your skin and the sauna wrap at all times.
• DO NOT exceed a 50-minute session (10-minute preheat with a 50-minute session).
• Ensure the device is unplugged and cooled down for 30 minutes prior to cleaning or storing.
• DO NOT dry clean, bleach, or submerge in water. DO NOT machine wash.

Package Contents

Your Sharper Image Calming Heat Sauna Wrap package includes:

• 1 Calming Heat Sauna Wrap
• 1 Digital Controller
• Instruction Manual

Image: The packaging box for the Calming Heat Sauna Wrap, showing the product and its key features.

Setup

1. Unpack and Lay Flat

   Carefully remove the Calming Heat Sauna Wrap from its packaging. Unfold the wrap and lay it flat on a heat-resistant surface, such as a bed or floor. Ensure there are no folds or creases that could trap heat.

   

   Image: The Calming Heat Sauna Wrap laid out flat, showing the attached controller.

2. Prepare for Use

   Place a towel over a pillow to rest your head comfortably. Ensure you are wearing loose-fitting, breathable clothing made of cotton to create a barrier between your skin and the wrap.

   

   Image: A woman demonstrating appropriate loose-fitting, skin-covering clothing for using the sauna wrap.

3. Connect Power

   Plug the power cord of the digital controller into any standard 120-volt AC electrical outlet.

Operating Instructions

1. Power On and Preheat

   Press the power/heat up button on the digital controller for 1 second to turn on the device. The display will illuminate. Preheat the wrap at a heat level of 3-5 for 10 minutes. Check the internal temperature by touching the inside of the wrap before entering. (Refer to the instructional video in the Setup section for visual guidance.)

2. Adjust Heat and Timer

   Quickly press the "Heat Up" or "Heat Down" buttons to adjust the heat intensity (8 settings available). Press the "Timer" button to select your session duration in 15-minute increments, up to a total of 1 hour. The massage feature has a separate 15-minute auto-off feature.

   

   Image: Close-up of the digital controller, showing buttons for heat, vibration, and timer adjustments.

3. Using the Wrap

   Lie down inside the wrap. The wrap features armholes for comfort and accessibility. The maximum interior circumference when in use is approximately 65 inches. Start at a heat level of 3-5. If you are able to sweat at these settings, there is no need to go to higher levels. If you are unable to sweat, slowly increase to level 6 or 7. It may take up to 20 minutes to produce a sweat. (Refer to the instructional video in the Setup section for visual guidance.)

   

   Image: A man relaxing inside the sauna wrap, demonstrating the open design for head and arms.

Maintenance

1. Cleaning

   The Sauna Wrap is not machine washable. After each use, ensure the device is unplugged and cooled down for at least 30 minutes. Use a damp rag with a mild detergent soap to wipe down any sweat from the interior. Optional non-toxic cleaning wipes can be used as a substitute. Wipe clean and allow to air dry completely before folding. (Refer to the instructional video in the Setup section for visual guidance.)

2. Storage

   Once clean and dry, fold the wrap vertically, then fold it into three equal sections for compact storage. Store in a cool, dry place. (Refer to the instructional video in the Setup section for visual guidance.)

Troubleshooting

• Controller Not Turning On

  If the controller does not turn on, unplug the cord from the outlet, wait 5 minutes, and then plug the unit in again to reset it.

• Sauna Wrap Not Feeling Hot Enough

  Preheating the device for 10 minutes will allow the Sauna Wrap to reach full temperature. Check the temperature with your hand prior to entering. If the temperature is too hot, adjust the heat setting and check again after a few minutes.

• Error Code "F" Displayed

  If the controller displays an "F" error code, this typically indicates a malfunction. Please refer to the warranty section for support.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact Sharper Image customer service directly. Keep your purchase receipt for warranty claims.