1. Important Safety Instructions
Please read and save these important safety instructions before using this fan. Failure to follow these instructions may result in electric shock, fire, or injury.
- Always unplug the fan before moving it, cleaning, or performing any maintenance.
- Do not use the fan near water or in wet locations.
- Keep the fan out of reach of children and pets.
- Ensure the fan is placed on a stable, level surface to prevent tipping.
- Do not insert fingers or any objects through the grille when the fan is operating.
- Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit condition. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the servicing instructions. If the replacement fuse blows, a short-circuit condition may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
- This fan is for indoor use only.
2. Package Contents
Verify that all components are present and in good condition:
- Fan Head Assembly (Motor, Blades, Grilles)
- Adjustable Stand Pole
- Base Legs (4 pieces)
- Base Connectors
- Power Cord
- Instruction Manual
3. Assembly Instructions
Follow these steps to assemble your PELONIS Pedestal Fan:
- Install Base: Insert the four base legs into the cross base connectors. Ensure they are securely fitted.
- Attach Stand Pole: Secure the adjustable stand pole to the assembled base. Tighten any securing nuts or screws provided.
- Mount Fan Head: Place the fan motor assembly onto the top of the stand pole. Secure it firmly with the provided nut.
- Attach Rear Grille: Align the rear grille with the motor housing and secure it.
- Install Fan Blades: Carefully place the fan blades onto the motor shaft. Ensure they are properly seated.
- Attach Front Grille: Align the front grille snaps with the top line of the rear grille and snap it into place. Secure with any clips or screws.
Figure 1: Step-by-step assembly guide for the PELONIS Pedestal Fan.
4. Operating Instructions
Familiarize yourself with the fan's controls and features for optimal use.
4.1 Power and Speed Settings
- Plug the fan into a standard 120V AC electrical outlet.
- Use the mechanical rotary dial located on the fan head to select your desired speed: 1 (Low), 2 (Medium), or 3 (High). Turn the dial to 0 (Off) to power down the fan.
Figure 2: Rotary dial for adjusting fan speed.
4.2 Oscillation Function
- To activate the 90° wide-angle oscillation, press down the oscillation knob located on top of the motor housing.
- To stop oscillation and direct airflow in a fixed position, pull up the oscillation knob.
Figure 3: Fan head demonstrating wide-angle oscillation and tilt adjustment.
4.3 Height and Tilt Adjustment
- Adjusting Height: Loosen the height adjustment knob on the stand pole, raise or lower the pole to the desired height (between 35 and 47 inches), and then securely tighten the knob.
- Adjusting Tilt: The fan head can be tilted up or down to direct airflow. Gently push or pull the fan head to achieve the desired angle.
Figure 4: Adjustable height feature of the pedestal fan.
5. Maintenance and Cleaning
Regular cleaning and maintenance will ensure optimal performance and longevity of your fan.
- Always unplug the fan before cleaning.
- Use a soft, damp cloth to wipe the exterior surfaces of the fan. Do not use abrasive cleaners or solvents.
- To clean the fan blades, remove the front grille by releasing its clips. Wipe the blades with a soft, damp cloth. Ensure blades are completely dry before reattaching the grille.
- Do not immerse the fan in water or allow water to drip into the motor housing.
- Store the fan in a cool, dry place when not in use.
6. Troubleshooting
If your fan is not operating correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not turn on | No power to the unit; Fan not plugged in; Blown fuse in plug | Check power outlet; Ensure plug is fully inserted; Replace fuse in plug (refer to safety instructions). |
| Weak airflow | Fan speed set too low; Grilles or blades are dirty | Increase fan speed setting; Clean grilles and blades as per maintenance instructions. |
| Fan is noisy | Loose parts; Fan not on a level surface | Check for loose screws or components; Place fan on a stable, level surface. |
| Oscillation not working | Oscillation knob not engaged/disengaged correctly | Press down the oscillation knob to activate; Pull up to stop. |
7. Specifications
- Model: PFS40M2ABB
- Brand: PELONIS
- Color: Black
- Fan Size: 16 inches
- Power Source: Corded Electric
- Number of Speeds: 3
- Oscillation: 90° Wide-Angle
- Adjustable Height: 35" to 47"
- Product Dimensions (D x W x H): 27" x 27" x 47" (at max height)
- Item Weight: 5.7 Pounds
- Noise Level: 45 Decibels
- Wattage: 32 watts
- Voltage: 120V
- Material: Plastic
- Safety Certification: ETL Listed
- Indoor/Outdoor Use: Indoor
8. Warranty and Support
Your PELONIS Pedestal Fan is backed by a 1-Year Manufacturer's Warranty.
For warranty claims, technical support, or replacement parts, please contact PELONIS customer service. Keep your purchase receipt as proof of purchase.
For more information, visit the official PELONIS website or refer to the contact details provided in your product packaging.
