Introduction
This manual provides comprehensive instructions for the setup, operation, and maintenance of your MIEFL Motion Sensor Toilet Light. Please read this manual thoroughly before use to ensure proper functionality and longevity of the product.
Package Contents
Verify that all items are present in your package:
- 2 x MIEFL Motion Sensor Toilet Lights
- User Manual (this document)
Note: 3 AAA batteries per unit are required and are not included in the package.
Setup and Installation
1. Battery Installation
- Locate the battery compartment on the back of the toilet light unit.
- Open the battery compartment cover.
- Insert 3 AAA batteries, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
Figure 1: Battery installation for the MIEFL Toilet Light. Ensure correct battery orientation.
2. Mounting the Device
- Adjust the flexible arm of the toilet light to fit over the rim of your toilet bowl.
- Position the main unit on the outside of the toilet bowl, ensuring the motion sensor faces outwards and upwards.
- Ensure the LED light strip is positioned inside the toilet bowl, below the rim, and securely in place.
Figure 2: Step-by-step guide for mounting the toilet light onto the toilet bowl rim.
Operating Instructions
Motion and Light Sensing
The MIEFL Toilet Light is equipped with both motion and light sensors:
- Motion Activation: The light will activate when motion is detected within approximately 6.6 feet (2 meters).
- Light Sensing: The device is designed to operate only in dark conditions to conserve battery life. It will not activate in a well-lit environment.
- Automatic Shut-off: The light will automatically turn off after approximately 2 minutes of no detected motion.
Figure 3: The toilet light's smart sensing capabilities for night activation and daytime energy saving.
Color Selection
The toilet light offers 16 different colors. By default, the light cycles through all 16 colors. To select a fixed color:
- Locate the small button on the side of the main unit (labeled 'Color Control Switch' in Figure 4).
- Press this button once while the light is cycling through colors. The light will stop on the current color.
- To return to the color-cycling mode, press the button again.
Figure 4: Location of the Color Control Switch and Motion Sensor on the MIEFL Toilet Light.
Brightness Adjustment
The toilet light features 5 brightness levels and automatically adjusts its brightness based on ambient light conditions. This feature is designed to optimize power consumption and extend battery life.
Maintenance
Cleaning
To clean your MIEFL Toilet Light:
- Remove the unit from the toilet bowl.
- Wipe the unit with a damp cloth and mild detergent.
- Do not submerge the main unit in water. The LED strip is waterproof, but the main unit containing electronics is not designed for full submersion.
- Ensure the unit is completely dry before re-installing or replacing batteries.
Figure 5: The LED light strip is waterproof for easy cleaning.
Battery Replacement
When the light begins to dim or fails to activate, it is time to replace the batteries. Follow the steps outlined in the 'Battery Installation' section (Section 1.1).
Troubleshooting
| Issue | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No batteries, dead batteries, incorrect battery polarity, or too much ambient light. | Check battery installation and replace if necessary. Ensure the environment is dark enough for activation. |
| Light turns on randomly or stays on. | Motion sensor obstructed or faulty, or unit is in a high-traffic area. | Ensure the motion sensor is clear. Reposition the unit if it's detecting unwanted motion. |
| Colors are not changing. | Fixed color mode is active. | Press the 'Color Control Switch' button to return to cycling mode. |
| Light is dim. | Low batteries. | Replace batteries. |
Product Specifications
| Feature | Specification |
|---|---|
| Model Number | LD-TL-JIU |
| Brand | MIEFL |
| Power Source | 3 x AAA Batteries (Not Included) |
| Light Source Type | LED |
| Number of Colors | 16 |
| Brightness Levels | 5 (Automatic Adjustment) |
| Motion Sensor Range | Approx. 6.6 ft (2 meters) |
| Auto Shut-off Duration | Approx. 120 seconds (2 minutes) |
| Material | Plastic (Acrylonitrile Butadiene Styrene) |
| Water Resistance Level | Waterproof (LED strip) |
| Product Dimensions | 4"D x 2.75"W x 2"H |
| Item Weight | 3.2 ounces |
| UPC | 735372412532 |
Warranty and Support
MIEFL products are designed for reliability and performance. For specific warranty details, please refer to the product packaging or contact MIEFL customer support directly. If you encounter any issues not covered in the troubleshooting section, please reach out to the seller or manufacturer for assistance.
