Introduction
The AGLENA corner whirlpool bathtub is designed to provide a luxurious and relaxing bathing experience. Featuring a modern design, it includes advanced hydrojet massage systems and a unique cascade water feature. This manual provides essential information for the safe installation, operation, and maintenance of your new bathtub.
Key features include 8 hydrojets (4 lateral and 4 back), a hand shower, and two comfortable headrests, all designed to enhance your relaxation.
Safety Information
- Always ensure the bathtub is properly grounded by a qualified electrician.
- Do not operate the hydrojet system without sufficient water in the tub.
- Keep electrical components dry and away from water splashes.
- Children and individuals with health conditions should be supervised when using the bathtub.
- Avoid using abrasive cleaners or harsh chemicals that may damage the acrylic surface.
- Ensure proper ventilation in the bathroom to prevent excessive humidity.
Setup and Installation
The AGLENA bathtub is designed for floor-standing installation. Due to its size and weight, professional installation by a licensed plumber and electrician is highly recommended to ensure proper water and electrical connections.
Figure 1: Front view of the AGLENA Corner Whirlpool Bathtub, showcasing its compact corner design and integrated features.
Pre-Installation Checks:
- Verify the floor can support the weight of the filled bathtub (approximately 350 liters of water + 82 kg tub weight + user weight).
- Ensure adequate space for the 150 cm x 150 cm footprint and 60 cm height.
- Confirm availability of 220-240V, 50Hz electrical supply with appropriate circuit protection.
- Prepare water supply lines (hot and cold) and drainage connections.
Installation Steps (Summary - Consult a Professional):
- Position the bathtub in the desired corner, ensuring the adjustable feet are level.
- Connect the hot and cold water supply lines to the integrated faucet system.
- Install the included siphon and connect it to the main drainage system.
- Connect the electrical pump to the dedicated power outlet, ensuring all connections are waterproof and meet local electrical codes.
- Perform a leak test by filling the tub and running the jets before final sealing.
- Install the front apron (tablier) if not pre-attached.
Operating Instructions
Familiarize yourself with the controls before first use.
Figure 2: Close-up of the integrated controls and hand shower for water flow and jet activation.
Filling the Bathtub:
- Turn the main faucet knob to fill the tub with water to the desired level. Ensure the water level is above the highest jet before activating the massage system.
- The integrated cascade system provides a unique water flow.
Figure 3: The elegant cascade water feature, providing a soothing visual and auditory experience.
Using the Hydrojet System:
- Once the tub is filled, locate the hydrojet activation button on the control panel.
- Press the button to activate the 8 hydrojets (4 lateral and 4 back).
- Adjust the intensity of the jets if a control is available (refer to specific knob functions).
- To turn off the jets, press the activation button again.
Using the Hand Shower:
- Pull out the hand shower from its holder.
- Use the diverter knob on the control panel to switch water flow from the main faucet/cascade to the hand shower.
- Adjust water temperature and flow using the main faucet knobs.
Headrests:
- The two integrated headrests are designed for maximum comfort during your bath.
Maintenance
Regular cleaning and maintenance will ensure the longevity and optimal performance of your AGLENA bathtub.
Figure 4: Overhead view highlighting the placement of hydrojets and headrests for comprehensive cleaning.
Cleaning the Bathtub Surface:
- Use a soft cloth or sponge with mild, non-abrasive bathroom cleaner.
- Rinse thoroughly with clean water after cleaning to remove all soap residue.
- For stubborn stains, consult a specialized acrylic bathtub cleaner. Avoid acetone, ammonia, or abrasive powders.
Hydrojet System Cleaning:
- Periodically fill the tub with warm water and add a small amount of non-foaming jet cleaner or white vinegar.
- Run the hydrojet system for 10-15 minutes to circulate the cleaning solution.
- Drain the tub and refill with clean water, then run the jets again for a few minutes to rinse the system.
Drain and Siphon Maintenance:
- Regularly check the drain for hair and debris to prevent blockages.
- Clean the siphon periodically as needed to ensure efficient drainage.
Troubleshooting
This section addresses common issues you might encounter with your AGLENA bathtub. For complex problems, contact a qualified technician.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hydrojets not working | Insufficient water level; Power supply issue; Pump malfunction. | Ensure water level is above jets. Check power connection and circuit breaker. Contact service if pump is faulty. |
| Weak jet pressure | Clogged jets; Low water pressure; Pump issue. | Clean jets as per maintenance section. Check household water pressure. Contact service for pump inspection. |
| Water not draining | Clogged drain or siphon. | Remove drain cover and clear any debris. Clean siphon if accessible. |
| Unusual noise from pump | Air in system; Loose components; Pump bearing issue. | Ensure tub is adequately filled. Check for loose connections. Contact service for pump inspection. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | AGLENA |
| Brand | Vente-unique |
| Type | Corner Whirlpool Bathtub with Cascade System |
| Capacity | 350 Liters |
| Dimensions (L x W x H) | 150 cm x 150 cm x 60 cm |
| Material | Reinforced Acrylic (7mm thickness) |
| Color | White |
| Number of Places | 2 places |
| Number of Hydrojets | 8 (4 lateral, 4 back) |
| Water Pump Power | 0.8 cv (580W high-pressure pump) |
| Power Supply | 220-240V, 50Hz |
| Noise Level (Motor) | 60 dB |
| Installation Type | Floor-standing |
| Included Equipment | Headrests, Apron (Tablier), Hand Shower, Siphon, Faucet with Cascade Spout |
| Product Weight | 82 Kilograms |
Warranty and Support
For warranty information and customer support, please refer to the terms and conditions provided at the time of purchase or visit the official Vente-unique website. Vente-unique is committed to customer satisfaction, with 94% of clients satisfied and over 2 million clients served across Europe.
Keep your purchase receipt and product details (model name, date of purchase) handy when contacting support.
For further assistance, you may contact Vente-unique customer service through their official channels.