1. Introduction
The Claber Meteocometa 6 Zone 8017 is a professional irrigation programmer designed for efficient management of watering systems, including drip irrigation and micro-irrigation. This device is capable of managing up to 6 independent irrigation zones and offers advanced programming features to optimize water usage.
Key features include:
- Manages up to 6 zones with two independent programs (A and B).
- Supports up to 4 daily start times.
- Adjustable irrigation durations from 1 minute to 4 hours and 15 minutes.
- Weekly and cyclic programming options (up to 12 days).
- Includes water balance, rain stop, and test functions.
- Connectable to the Claber Rain Sensor for automatic rain detection.
- Equipped with an internal 230/24V 50/60Hz transformer and a 9V buffer battery for memory retention.
2. Setup and Installation
Before operating the Claber Meteocometa 8017, ensure proper installation and power connection.
2.1 Power Connection
The programmer operates with an internal 230/24V 50/60Hz transformer. Connect the device to a suitable power outlet. A 9V buffer battery (not supplied) should be installed to maintain programming memory during power outages.
Figure 2.1: Claber Meteocometa 8017 with its power cord, ready for connection. This image shows the overall unit with the protective cover closed and the power cable extending from the side.
2.2 Zone Connections
Connect your irrigation valves to the corresponding zone terminals on the programmer. The device supports up to 6 independent zones.
2.3 Rain Sensor Connection (Optional)
The Meteocometa 8017 can be connected to a Claber Rain Sensor (sold separately) to automatically suspend irrigation during rainfall, conserving water. Refer to the Rain Sensor's manual for specific connection instructions.
3. Operating Instructions
The control panel allows for easy programming and management of irrigation cycles.
Figure 3.1: Front view of the Claber Meteocometa 8017 control panel with the protective cover open, showing the LCD display, navigation buttons (A, B, EXIT, ENTER), and programming keys.
3.1 Initial Time and Date Setting
- Press the ENTER button to access the main menu.
- Navigate using the A or B buttons to select "SET TIME" or "SET DATE".
- Press ENTER to confirm and use A or B to adjust values.
- Press ENTER to move to the next field or confirm the setting.
- Press EXIT to return to the main display.
3.2 Programming Irrigation Cycles
The programmer supports two independent programs, A and B, for flexible scheduling.
3.2.1 Setting Program A/B
- From the main display, press ENTER.
- Navigate to "PROGRAM A" or "PROGRAM B" using A or B.
- Press ENTER.
- Follow the on-screen prompts to set:
- Start Times: Up to 4 per day.
- Irrigation Duration: For each zone, from 1 minute to 4 hours and 15 minutes.
- Days of the Week: Select specific days for irrigation.
- Cyclic Programming: Set irrigation cycles up to 12 days (e.g., every 2 days).
- Use A or B to adjust values and ENTER to confirm.
- Press EXIT to save and return.
3.2.2 Manual Operation
To manually start or stop irrigation for a specific zone:
- Press the MANUAL button.
- Use A or B to select the desired zone.
- Press ENTER to start irrigation. Press again to stop.
3.2.3 Rain Stop Function
If a Rain Sensor is connected, the system will automatically pause irrigation during rain. You can also manually activate the rain stop function from the menu if needed.
3.2.4 Water Balance Function
This feature allows for seasonal adjustment of irrigation durations across all active programs. Access it through the main menu to increase or decrease watering times by a percentage.
3.2.5 Test Function
The test function allows you to quickly run through all programmed zones for a short duration to verify connections and operation. Access it from the main menu.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your Claber Meteocometa 8017.
- Cleaning: Periodically wipe the exterior of the programmer with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Battery Check: If a 9V buffer battery is installed, check its charge annually and replace it if necessary to prevent loss of programming during power outages.
- Environmental Protection: Ensure the programmer is installed in a location protected from direct sunlight, extreme temperatures, and heavy rain, unless specifically designed for outdoor exposure.
5. Troubleshooting
This section provides solutions to common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Programmer display is blank. | No power supply or faulty transformer. | Check power outlet and transformer connection. Ensure the outlet is active. |
| Irrigation does not start. | Incorrect programming, valves not connected, or rain sensor active. | Verify program settings (start times, durations, days). Check valve wiring. Ensure rain sensor is dry or temporarily bypass it for testing. |
| Programmer loses settings after power outage. | 9V buffer battery is dead or not installed. | Install a new 9V alkaline battery or replace the existing one. |
| Watering continues during rain. | Rain sensor not connected or faulty. | Check rain sensor connection. Ensure the sensor is clean and functioning correctly. |
If the problem persists after attempting these solutions, please contact Claber customer support or a qualified technician.
6. Specifications
| Feature | Detail |
|---|---|
| Model | Meteocometa 8017 |
| Zones Managed | Up to 6 independent zones |
| Programs | 2 independent (A and B) |
| Daily Start Times | Up to 4 per day per program |
| Irrigation Duration | 1 minute to 4 hours 15 minutes |
| Programming Options | Weekly, Cyclic (up to 12 days) |
| Special Functions | Water balance, Rain stop, Test function |
| Power Supply | Internal transformer 230/24V 50/60Hz |
| Buffer Battery | 9V (not supplied) for memory retention |
| Rain Sensor Compatibility | Yes, with Claber Rain Sensor |
| ASIN | B09X68B4QW |
| First Available Date | November 16, 2023 |
7. Warranty and Support
Specific warranty information for the Claber Meteocometa 8017 is not provided in this manual. For details regarding warranty coverage, terms, and conditions, please refer to the documentation included with your purchase or visit the official Claber website.
For technical support, spare parts, or service inquiries, please contact Claber customer service through their official channels. Ensure you have your product model number (8017) and purchase details available when seeking support.
