REDTIGER Dash Cam Hardwire Kit Instruction Manual

Introduction

This instruction manual provides comprehensive guidance for the installation, operation, and maintenance of your REDTIGER Dash Cam Multi-Size Hardwire Kit. This kit is designed to provide a continuous power supply to your dash camera, enabling 24-hour parking monitoring with integrated low voltage protection and a convenient voltage indicator. Please read this manual thoroughly before installation to ensure proper setup and optimal performance.

Package Contents

Verify that all items listed below are included in your package:

• REDTIGER Dash Cam Hardwire Kit (with USB-C power port and voltage indicator)
• Multiple Fuse Adapters (various sizes)
• Installation Tool (crowbar)

Image: Complete REDTIGER Hardwire Kit showing all included components.

Key Features

• Universal Compatibility: 12V to 24V input, delivering a consistent 5V/3A MAX to REDTIGER dash cams via Type-C ports. Includes four types of fuse adapters in two sets for broad vehicle compatibility.
• Easy Installation: Designed for hidden wiring, eliminating the need for a car cigarette lighter socket. Includes an installation tool for a clean setup.
• Continuous Monitoring: Taps directly into the car battery or fuse box, providing constant power for 24-hour parking monitoring, even when the vehicle is switched off.
• Low Voltage Protection: Automatically cuts off power after 60 seconds if the voltage drops below 11.8V (+/-0.2V) to prevent car battery drain. Not suitable for trucks with voltage above 24V.
• Multiple Security Protection: Includes safeguards against over-current, short-circuit, reverse connection, and overheating.
• Voltage Readout Feature: Built-in display allows real-time monitoring of the vehicle's voltage.

Setup & Installation

This section provides detailed steps for installing your REDTIGER Hardwire Kit. It is strongly recommended to refer to your vehicle's manual or seek professional assistance if you are unsure about any steps.

Installation Video Guide

Step-by-Step Installation

1. Preparation:

   Ensure everything is ready and safe before beginning the installation. Turn off your vehicle's ignition and disconnect the negative terminal of your car battery for safety.

2. Locate the Fuse Box:

   The car's fuse box is typically located under the dashboard on the driver's side or in the engine compartment. In some vehicles, like certain BMW models, it might be found in the trunk.

   

   Image: Example of a car's fuse box, often found in the trunk or under the dashboard.

3. Identify ACC and Constant Power Fuse Slots:

   Identify the ACC (Accessory) fuse slot in the fuse box. This slot provides power only when the ignition is on. Locate the constant power fuse slot, which provides power even when the ignition is off (for parking monitoring).

   Refer to your vehicle's fuse box diagram (usually on the fuse box cover or in the owner's manual) to identify these specific terminals. The terminal that still has current after the car is turned off is the B+ (constant power), while the terminal that loses power after the car is turned off is the ACC. (Note: Some car models have a delayed power-off feature for the ACC terminal, so it is necessary to wait until the power is completely cut off before conducting the test.)

   

   Image: Different types of fuse adapters provided to match various vehicle fuse box configurations.

4. Connect the Wires:

   • Connect the red wire from the hardwire kit to the ACC fuse slot using an appropriate fuse tap.
   • Connect the yellow wire from the hardwire kit to the constant power (B+) fuse slot using an appropriate fuse tap.
   • Find a suitable grounding point near the fuse box (a metal surface securely connected to the vehicle's chassis). Connect the black wire from the hardwire kit to this grounding point using the ring terminal or suitable connector.
   

   Image: Proper connection of the hardwire kit's red, yellow, and black wires to the fuse box and ground.

5. Route the Cable:

   Use the provided installation tool (crowbar) to hide the remaining wire along the gap of the front windshield, down the A-pillar, and along the gap between the car body and the ceiling on the side of the passenger seat, and between the rear seat and the ceiling, leading to the dash cam's mounting location.

   

   Image: Demonstrating how to tuck the cable neatly along the windshield and A-pillar using the installation tool.

   

   Image: Illustrating the cable routing path towards the rear of the vehicle for a clean installation.

6. Final Check:

   Once all connections are secure and wires are neatly routed, reconnect the negative terminal of your car battery. Test the hardwire kit by turning on the ignition. The dash cam should receive power and begin functioning.

Important Note:

The REDTIGER Hardwire Kit is compatible with all REDTIGER series dash cams (e.g., F7N/F7NP/F7NT/F7NS/F8/F9/F17/F4/F77 Mini Dash Cam and T27/T700 Mirror Dash Cams etc.). It is not suitable for dash cams from other brands.

Image: Visual representation of the hardwire kit and compatible REDTIGER dash cam models.

Operating Instructions

24H Parking Monitoring

Once correctly installed, the hardwire kit enables your compatible REDTIGER dash cam to continuously monitor your vehicle for 24 hours. This feature is active even when your car's ignition is off, providing surveillance against potential incidents.

Image: Illustrates the 24-hour parking monitoring capability, providing continuous protection for your vehicle.

Voltage Readout

The hardwire kit features a built-in voltage indicator. This display provides real-time information on your vehicle's battery voltage, allowing you to monitor its status directly from the hardwire unit.

Maintenance

The REDTIGER Hardwire Kit is designed for durability and requires minimal maintenance. To ensure longevity and optimal performance:

• Periodically check all connections to ensure they remain secure.
• Keep the hardwire unit and cables free from excessive dust or moisture.
• Avoid exposing the unit to extreme temperatures outside of normal vehicle operating conditions.

Troubleshooting

If you encounter issues with your hardwire kit, consider the following common solutions:

• Dash Cam Not Powering On:
  • Ensure all three wires (red, yellow, black) are correctly connected to their respective terminals (ACC, B+, Ground).
  • Verify that the fuse taps are properly inserted into the fuse box and that the original fuses are correctly placed within the taps.
  • Check your vehicle's fuses to ensure none are blown.
• Parking Monitoring Not Working:
  • Confirm the yellow wire (B+) is connected to a constant power source that remains active when the ignition is off.
  • Ensure your dash cam's parking mode feature is enabled and configured correctly according to its own manual.
• Low Voltage Cut-off Issues:
  • The kit is designed to protect your car battery. If the voltage drops below 11.8V, it will cut off power. This is normal operation.
  • If the cut-off occurs too frequently, consider checking your car battery's health or reducing the parking monitoring duration if your dash cam allows.
• Voltage Indicator Not Displaying:
  • Ensure the hardwire kit is receiving power.
  • Check for any damage to the voltage indicator unit itself.

If problems persist, please contact REDTIGER customer support for further assistance.

Specifications

Warranty & Support

REDTIGER is committed to providing high-quality products and excellent customer service. Your hardwire kit comes with the following:

• 18 Months Protection: Enjoy extended coverage for your product.
• 7 Days Return Policy: For returns based on change of mind or non-defective reasons.
• Return on Defects: Hassle-free returns for any manufacturing defects.

For any professional help or inquiries, please feel free to reach out to REDTIGER customer support. We offer 24-hour support via email and phone.

You can also refer to the official User Manual (PDF) for additional information.