1. Introduction
The Nerf Pro Gelfire Mythic Full Auto Blaster delivers high-performance blasting with hydrated rounds that burst on impact. Designed for ages 14 and up, this blaster features full-auto and semi-auto modes, a high-capacity 800-round hopper, and a convenient rechargeable battery. This manual will guide you through the setup, operation, and maintenance of your new Gelfire blaster to ensure a safe and enjoyable experience.
2. Important Safety Information
WARNING: Small parts may be generated. Not for children under 3 years.
EYEWEAR REQUIRED: Always wear the included protective eyewear when using this blaster. Do not aim at eyes or face. Use only official Nerf Gelfire Rounds. Do not freeze or modify rounds. Do not modify blaster. Impact from rounds may cause temporary marks on skin. Adult supervision is recommended.
3. What's in the Box
- Nerf Pro Gelfire Mythic Blaster
- Rechargeable 7.4V 500mAh LiPo Battery
- 800-Round Capacity Hopper
- Removable Barrel Attachment
- 2 x 5,000-Round Packets of Dehydrated Nerf Pro Gelfire Soft Super Absorbent Polymer Projectiles (10,000 total)
- Protective Eyewear
- Universal USB-A to USB-C Charging Cable (USB-A wall charger not included)
Figure 3.1: All included components of the Nerf Pro Gelfire Mythic Blaster.
4. Setup
4.1 Hydrating Gelfire Rounds
- Empty the dehydrated Nerf Pro Gelfire rounds into a large container.
- Add plenty of clean tap water to fully submerge the rounds.
- Allow the rounds to soak for 3 to 4 hours. They will expand significantly.
- Drain any excess water before use. The hydrated rounds are now ready for loading.
Figure 4.1: Gelfire rounds hydrating in water.
Figure 4.2: Dehydrated vs. Hydrated Gelfire Rounds.
4.2 Charging the Rechargeable Battery
- Locate the rechargeable 7.4V 500mAh LiPo battery.
- Connect the battery to the included USB-A to USB-C charging cable.
- Plug the USB-A end of the cable into a compatible USB-A wall charger (not included).
- Allow the battery to charge for approximately 2 hours for a full charge. The indicator light on the battery will change to show charging status.
Figure 4.3: Rechargeable Battery.
4.3 Blaster Assembly
- Insert the charged rechargeable battery into the designated slot on the blaster. Ensure it clicks securely into place.
- Attach the extendable stock to the rear of the blaster by sliding it into position until it locks.
- Twist and attach the removable barrel to the front of the blaster.
- Ensure all attachments are firmly secured before use.
Figure 4.4: Assembled Nerf Pro Gelfire Mythic Blaster.
Video 4.1: Official demonstration of the Nerf Pro Gelfire Mythic Blaster, showing battery insertion, round hydration, and firing modes.
5. Operating the Blaster
5.1 Loading the Hopper
- Open the lid of the 800-round capacity hopper.
- Carefully pour the hydrated Gelfire rounds into the hopper.
- Close the hopper lid securely.
- Attach the filled hopper to the top rail of the blaster, ensuring it is locked in place.
Figure 5.1: Blaster with hopper attached.
5.2 Firing Modes
- Ensure your protective eyewear is on.
- Locate the power switch/mode selector on the blaster.
- Turn the blaster ON. The indicator light will illuminate.
- Select your desired firing mode:
- Semi-Auto Mode: Pull the trigger once for each round you wish to fire.
- Full-Auto Mode: Hold down the trigger for continuous blasting at up to 10 rounds per second.
- To activate the trigger lock, slide the orange safety switch located near the trigger. This prevents accidental firing.
Figure 5.2: Blaster trigger and mode selector.
6. Maintenance
6.1 Cleaning
Wipe down the blaster with a damp cloth as needed. Do not submerge the blaster in water. Ensure no water enters the internal electronic components.
6.2 Storing Gelfire Rounds
Store hydrated Gelfire rounds in an airtight container away from direct sunlight and extreme temperatures to prevent them from drying out. If rounds dry out, they can be rehydrated by soaking them in water again.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Blaster not firing / Rounds getting stuck | Rounds not fully hydrated or jammed in the feeding mechanism. | Ensure rounds are fully hydrated (3-4 hours soak time). Gently shake the blaster to dislodge any stuck rounds. If the issue persists, remove the hopper and clear any visible obstructions. |
| Blaster not turning on | Battery is not charged or not properly inserted. | Ensure the rechargeable battery is fully charged and correctly inserted into the blaster. Check the power switch is in the 'ON' position. |
| Low firing velocity | Battery charge is low. | Recharge the battery. Performance may decrease as the battery drains. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | F7267 |
| Brand | Nerf |
| Dimensions (L x W x H) | 14 x 2.62 x 10.5 inches |
| Item Weight | 1.5 pounds |
| Hopper Capacity | 800 rounds |
| Rounds Included | 10,000 dehydrated Gelfire rounds |
| Battery Type | Rechargeable 7.4V 500mAh LiPo (included) |
| Charging Cable | USB-A to USB-C (included) |
| Recommended Age | 14 years and up |
| Firing Modes | Full-Auto, Semi-Auto |
| Max Firing Rate | Up to 10 rounds per second (full-auto) |
| Material Type | Plastic |
9. Warranty and Support
For warranty information or product support, please contact Hasbro customer service directly. Refer to the packaging or Hasbro's official website for the most up-to-date contact details and warranty policies.
