Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your new ACROPIX Windshield Washer Motor Pump. Designed for specific Honda CR-V models, this pump ensures effective and consistent windshield fluid delivery for optimal visibility. Please read this manual thoroughly before beginning any installation or maintenance procedures.

2. Product Overview

The ACROPIX Windshield Washer Motor Pump is a direct replacement component engineered to meet or exceed OEM specifications. It is designed to restore proper windshield washing functionality to your vehicle.

Figure 2.1: The ACROPIX windshield washer motor pump, shown with its accompanying rubber grommet. This unit is designed for efficient fluid delivery.

Figure 2.2: Detailed view highlighting the electrical connection, washer fluid outlet, washer fluid inlet, and the rubber grommet. These are key components for proper function and installation.

3. Compatibility

This windshield washer motor pump is specifically designed to fit the following vehicle model:

• For Honda CR-V 5-door: 2007-2011 models

OE Numbers: 76806SMAJ02, 76806-SMA-J02, 76806-SMA-J01

4. Installation Guide

Replacing a windshield washer pump requires careful attention. While the process may appear straightforward, professional installation is highly suggested due to the potential need to remove multiple components in the front of the vehicle.

4.1. General Steps (Consult a professional or vehicle-specific repair manual for detailed instructions):

1. Safety First: Ensure the vehicle is turned off and the parking brake is engaged. Disconnect the negative terminal of the battery.
2. Access the Reservoir: Locate the windshield washer fluid reservoir. This often requires removing parts of the wheel well liner or bumper components.
3. Drain Fluid: If possible, drain the remaining washer fluid from the reservoir.
4. Disconnect Old Pump: Disconnect the electrical connector and the fluid hoses from the old washer pump. Be prepared for some fluid spillage.
5. Remove Old Pump: The pump is typically held in place by a rubber grommet. Gently pull the old pump out of the reservoir.
6. Install New Grommet (if applicable): If a new rubber grommet is provided, replace the old one in the reservoir opening. Ensure it is seated correctly to prevent leaks.
7. Install New Pump: Insert the new ACROPIX washer pump into the grommet in the reservoir. Apply a small amount of washer fluid to the grommet for easier insertion if needed. Ensure it is firmly seated.
8. Reconnect Hoses and Electrical: Reattach the fluid hoses to the correct outlets on the new pump. Reconnect the electrical connector.
9. Refill Reservoir: Fill the washer fluid reservoir with appropriate windshield washer fluid.
10. Test Functionality: Reconnect the battery. Turn on the vehicle and test the windshield washer system to ensure proper spray and no leaks.
11. Reassemble: Reinstall any removed vehicle components (wheel well liner, bumper parts, etc.).

Note: Online video tutorials specific to your vehicle model can be a helpful visual aid for this process. However, exercise caution and consider professional assistance if you are not comfortable with automotive repairs.

5. Operation

Once installed, the ACROPIX Windshield Washer Motor Pump operates automatically when the windshield washer function is activated from your vehicle's control stalk or button. The pump will draw fluid from the reservoir and propel it through the washer nozzles onto the windshield, or rear window if applicable.

Ensure the washer fluid reservoir is adequately filled for optimal performance. Using a high-quality windshield washer fluid is recommended for best results and to prevent nozzle clogging.

6. Maintenance

The windshield washer pump itself requires minimal maintenance. However, regular checks of the overall system are recommended:

• Fluid Level: Regularly check and refill the windshield washer fluid reservoir. Do not let it run dry, as this can strain the pump.
• Nozzle Inspection: Periodically check the washer nozzles for clogs or misalignment. Clean them if necessary.
• Hose Integrity: Inspect the fluid hoses for cracks, leaks, or loose connections.
• When to Replace:
  • If your vehicle is approximately 10 years old and components show signs of rust or wear.
  • If your windshield washers do not spray fluid, or if the spray is weak or uneven.
  • If the washer fluid reservoir shows signs of leaking around the pump area.
  • If you hear unusual noises from the pump motor when activated.

7. Troubleshooting

8. Specifications

Figure 8.1: Visual representation of the pump and grommet dimensions, including length, width, height, and diameters for accurate fitment.

9. Warranty and Support

For warranty information or technical support regarding your ACROPIX Windshield Washer Motor Pump, please refer to the product packaging or contact ACROPIX customer service directly. Contact details can typically be found on the manufacturer's official website or through your point of purchase.

For additional information and products, you may visit the official ACROPIX store: ACROPIX Store on Amazon.