glacio XJ-RGPE-LTAP-parent2
Contents
glacio Clear Ice Maker Set Instruction Manual
Model: XJ-RGPE-LTAP-parent2 | 2 Cavity - Sphere
Introduction
This manual provides comprehensive instructions for the safe and effective use of your glacio Clear Ice Maker Set. Please read this manual thoroughly before first use and retain it for future reference. The glacio Clear Ice Maker Set utilizes directional freezing technology to produce crystal clear ice spheres, enhancing the quality and presentation of your beverages.
Package Contents
Upon unboxing, please ensure all components are present and undamaged:
- 1x Insulated Container (Black)
- 1x Silicone Ice Ball Mold (2 Cavity - Sphere)
- 1x Lid for Silicone Mold

Image: The glacio Clear Ice Maker Set, showing the insulated container, the silicone mold, and a perfectly clear ice ball in a glass of whiskey.
Setup and First Use
- Initial Cleaning: Before first use, wash all components (insulated container, silicone mold, and lid) with warm, soapy water. Rinse thoroughly and allow to air dry.
- Assemble the Mold: Place the silicone ice ball mold into the insulated container. Ensure it sits securely at the bottom.
- Fill with Water: Fill the insulated container with water up to the designated fill line. This line is typically indicated by a vertical marker or a specific level within the container. Using filtered or distilled water is recommended for optimal clarity.
- Insert Silicone Lid: Carefully place the silicone lid onto the mold, pressing down gently. Excess water will overflow through the small holes on top of the mold. This is normal and part of the directional freezing process.
- Placement in Freezer: Transfer the assembled ice maker set to your freezer. Ensure it is placed on a flat, level surface to prevent spills and ensure even freezing.

Image: A person filling the insulated container with water in a kitchen sink.
Operating Instructions
- Freezing Time: Allow the ice maker to freeze for approximately 24-36 hours. The exact time may vary depending on your freezer's temperature and efficiency. For best results, avoid opening the freezer frequently during this period.
- Ice Removal:
- Once frozen, remove the entire unit from the freezer.
- Gently separate the silicone mold from the insulated container. The bottom section of the container may contain a layer of cloudy ice; this is expected as impurities are pushed downwards during directional freezing.
- Carefully peel back the silicone mold to release the clear ice spheres. If the ice is difficult to remove, allow the mold to sit at room temperature for a few minutes, or run a small amount of warm water over the exterior of the silicone mold.
- Serving: Place the clear ice sphere into your preferred beverage glass. The large, dense ice ball melts slowly, minimizing dilution and preserving the flavor of your drink.
- Storage: If not using immediately, store the clear ice spheres in an airtight container or freezer bag in your freezer to prevent freezer burn and maintain clarity.

Image: A hand carefully extracting a clear ice sphere from the silicone mold after freezing.
Video: Official glacio demonstration of the clear ice sphere mold, showing the filling, freezing, and ice removal process.
Care and Maintenance
- Cleaning: All components are dishwasher safe. Alternatively, wash by hand with warm, soapy water and rinse thoroughly.
- Drying: Ensure all parts are completely dry before reassembling or storing to prevent ice buildup or odors.
- Storage: Store the ice maker set in a clean, dry place when not in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Ice is cloudy or not perfectly clear. | Tap water contains dissolved minerals and air bubbles. Insufficient freezing time. | Use filtered or distilled water. Ensure the mold is completely filled. Allow for the full 24-36 hour freezing period. |
| Difficulty removing ice spheres from the mold. | Ice is too cold or mold is stuck. | Let the mold sit at room temperature for a few minutes, or run warm water over the exterior of the silicone mold for a few seconds. Gently peel the silicone away from the ice. |
| Water overflows excessively during filling. | Overfilling the insulated container before inserting the mold. | Ensure water is filled only up to the indicated fill line before inserting the silicone mold. |
Product Specifications
- Brand: glacio
- Model: XJ-RGPE-LTAP-parent2
- Type: Clear Ice Maker Set
- Cavity: 2 Cavity - Sphere
- Material: Premium Silicone
- Color: Black
- Ice Sphere Size: Approximately 2.4 inches
- Product Dimensions: 5.04"L x 8.82"W x 7.83"H
- Item Weight: 2.56 pounds (1.17 Kilograms)
- Dishwasher Safe: Yes
- UPC: 860008320933
Warranty Information
This glacio product is covered by a return policy that allows for refunds or replacements. For specific details regarding your product's warranty and return eligibility, please refer to the purchase platform or contact glacio customer support directly. Please retain your proof of purchase for any warranty claims.
Customer Support
For further assistance, product inquiries, or support, please visit the official glacio store or contact their customer service department.
- Manufacturer: Glacio
- Online Store: Visit the glacio Store on Amazon
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.